Bedienungsanleitung DeWalt DW711 T 7 (Seite 31 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

545014

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

3. Slide the fence towards the blade and tighten the locking knob.

4. Check that the fence is parallel to the blade.

5. If adjustment is required, proceed as follows:

6. Loosen the sliding fence locking knob (35) (fig. C1) and slide the sliding

fence backwards in order to obtain full sight on the two holes (36)

(fig.C4) in the top of the fence.

7. Using the small hex key, loosen the two hex screws fastening the fence

to the fence support. Access is gained through the two holes in the top

of the fence.

8. Adjust the fence so that it is parallel to the blade by checking the

distance between the blade and the fence at the front and rear of the

blade.

9. When the adjustment has been carried out, re-tighten the hex screws

and check again that the fence is parallel to the blade.

ADJUSTING THE SAW BENCH TABLE (FIG. A2, B, D)

The table (21) slides up and down manually and is held at the required

height with two locking knobs.

1. Loosen the table locking knobs, both main (37) (fig. D) and additional (3)

(fig. A1), but do not take them off.

2. Set the table to the proper height needed.

3. Tighten the table locking knobs (fig. A1, D).

REMOVING THE SAW BENCH TABLE (FIG. A1, B, D)

The table can be removed to gain access to the saw blade.

1. Remove the upper blade guard (16) (fig. B).

2. Loosen the table locking knobs, both main (37) (fig. D) and additional (3)

(fig. A1), but do not take them off.

3. Use the hex key to remove the screw (38) from the rear table column

(fig. D). Take the nut and washer off the other end of the screw.

4. Remove the table.

5. To replace the table, proceed in reverse order.

MOUNTING THE SAW BLADE (FIG. E1–E5)

WARNING: The teeth of a new blade are very sharp and can

be dangerous.

In order to fit a new saw blade it is necessary to adjust the table into highest

position and raise the saw head to its highest position.

1. Retract the lower guard (4) by pushing the release knob (42) in and

sliding the lower guard back. Leave the guard retracted.

2. Using the spanner (39), place the two holes on the outside of the outer

flange (40) (fig. E2).

3. Using the 6 mm hex key, turn the blade bolt (41) clockwise to loosen.

Remove the blade bolt and its outside flange.

4. Remove the saw blade (43).

5. Install the new saw blade onto the shoulder (44) on the inner flange (45)

(fig. E3). Ensure that the teeth at the bottom edge of the saw blade are

pointing towards the fence (away from the operator).

6. Reinstall the outer flange, making sure that the location lugs (46)

(fig. E4) are engaged correctly, one on each side of the spindle.

7. Tighten the blade bolt (41) by turning counterclockwise.

8. Move the lower guard down.

9. After mounting or replacing the saw blade, carry out a complete

movement of the saw head, checking that the movable lower guard

locks in its rest position.

WARNING: The saw blade MUST be replaced as described

in this section. ONLY use saw blades as specified under

Technical Data. We suggest DT4375. NEVER fit other saw

blades.

ADJUSTING THE SAW BLADE (FIG. E2)

If the saw blade is wobbling during start up and run down, then adjust as

follows.

1. Loosen the screw for the arbor collar (40) and rotate the blade (43) a

quarter turn.

2. Retighten the screw and check to see if the blade has any wobble.

3. Repeat these steps until the blade wobble has been eliminated.

MOUNTING AND REMOVING THE FIXED LOWER GUARD (FIG. I1, I2)

When the unit is being used as a saw bench, the fixed lower guard (18)

should always be used (fig. I2).

1. Set the saw head to the vertical position.

2. Loosen locking knob (60) on left side of fence (11) and move fence to

new position as shown (fig. I1).

3. Slide the guard (18) over the rotating table/mitre arm (9) until threads of

head lock down screw align with threaded bushing in head (fig. I2).

4. Depress the head lock up release lever (2) and press down on the head

while tightening the head lock down screw (20).

5. To remove the guard, proceed in reverse order.

STORING THE FIXED LOWER GUARD (FIG. Q1, Q2)

When the unit is being used in mitre saw mode, the fixed lower guard (18)

can be stored on the table (21).

1. Remove fixed lower guard, refer to Mounting and Removing the

Fixed Lower Guard.

2. Squeeze the fixed lower guard (18) and guide the storage legs (61) into

the slots (62) on the front of the table (21).

3. Push fixed lower guard until the storage legs (61) snap onto the table.

Figure Q2 shows the fixed lower guard in storage position.

4. To remove the guard, squeeze the fixed lower guard and lift guard from

table.

CHECKING AND ADJUSTING THE BLADE TO THE FENCE (FIG. F1–F4)

1. Slacken the mitre latch (8).

2. Place your thumb on the mitre lever (7) and squeeze the mitre latch (8)

to release the mitre arm (9) (fig. F1).

3. Swing the mitre arm until the latch locates it at the 0° mitre position.

4. Check that the two 0° markings (47) on the scale (10) are just visible

(fig. F2).

5. Place a square (48) against the left side of the fence (11) and blade (43)

(fig. F3).

WARNING: Do not touch the tips of the blade teeth with the

square.

If adjustment is required, proceed as follows:

1. Loosen the screws (49) and move the scale/mitre arm assembly left or

right until the blade is at 90° to the fence as measured with the square

(fig. F4).

2. Retighten the screws (49).

CHECKING AND ADJUSTING THE BLADE TO THE TABLE (FIG. G1–G4)

1. Loosen the bevel clamp handle (12) (fig. G1).

2. Press the saw head to the right to ensure it is fully vertical and tighten

the bevel clamp handle.

3. Place a set square (48) on the table and up against the blade

(43) (fig. G2).

WARNING: Do not touch the tips of the blade teeth with the

square.

If adjustment is required, proceed as follows:

1. Loosen the bevel clamp handle (12) (fig. G1) and turn the vertical

position adjustment stop screw (50) in or out (fig. G3) until the blade is

at 90° to the table as measured with the square (fig. G2).

2. If the bevel pointer (51) does not indicate zero on the bevel scale (52),

loosen the screws (53) that secure the scale and move the scale as

necessary (fig. G4).

CHECKING AND ADJUSTING THE BEVEL ANGLE (FIG. H1, H2)

The bevel override knob (54) allows the max. bevel angle to be set at 45°

or 48° as required (fig. H1).

– Left = 45°

– Right = 48°

1. Make sure the override knob (54) is located in the left position.

2. Loosen the bevel clamp handle (12) and move the saw head to the left.

This is the 45° bevel position.

3. If adjustment is required, proceed as follows:

4. Turn the stopscrew (55) in or out as necessary until the pointer (51)

indicates 45° (fig. H2).

DeWalt DW711 T 7 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info