545014

DeWalt DW711 T 7 Seite 32

32
Zoom out
Zoom in
Vorherige Seite
1/124
Nächste Seite
ENGLISH
30
WARNING: While performing this adjustment, it is advisable to
take the weight of the saw head by holding it. This will make it
easier to turn the adjustment screw.
ADJUSTING THE RIVING KNIFE (FIG. A2, J1, J2)
The correct position is for the top of the riving knife (15) to be no more than
2 mm below the highest tooth of the blade and the body of the radius knife
to be a maximum of 5 mm from the tips of the saw blade teeth (fig. J1)
1. Adjust the saw bench table to the lower position.
2. Loosen the hex screw (57) which allows both the bracket to rotate and
the riving knife to move up and down (fig. J2).
3. Rotate the bracket and slide the knife either up or down until the
correct position is attained.
4. Retighten the screw (57) firmly.
5. Replace the table.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing
and removing accessories, before adjusting or changing set-
ups or when making repairs. An accidental start-up can cause
injury.
WARNING:
• Ensure the machine is placed to satisfy ergonomic conditions
in terms of table height and stability. The machine site shall
be chosen so that the operator has a good overview and
enough free surrounding space around the machine that allow
handling of the workpiece without any restrictions.
• To reduce effects of vibration make sure the environment
temperature is not too cold, machine and accessory is well
maintained and the workpiece size is suitable for this machine.
• Ensure the material to be sawn is firmly secured in place.
• Apply only a gentle pressure to the tool and do not exert side
pressure on the saw blade.
• Avoid overloading.
• Always remove the dust from the machine after using to
ensure the lower guard operates properly.
The attention of UK users is drawn to the “woodworking machines
regulations 1974” and any subsequent amendments.
PRIOR TO OPERATION
• Install the appropriate saw blade. Do not use excessively worn blades.
The maximum rotation speed of the tool must not exceed that of the
saw blade.
• Do not attempt to cut excessively small pieces.
• Allow the blade to cut freely. Do not force.
• Allow the motor to reach full speed before cutting.
• Make sure all locking knobs and clamp handles are tight.
SWITCHING ON AND OFF (FIG. A1)
• To switch the machine on, press the on/off switch (1).
• To switch the machine off, press the on/off switch again.
Dust Extraction
WARNING: When ever possible, connect a dust extraction
device designed in accordance with the relevant regulations
regarding dust emission.
Connect a dust collection device designed in accordance with the relevant
regulations. The air velocity of externally connected systems shall be
20 m/s +/– 2 m/s. Velocity to be measured in the connection tube at the
point of connection, with the tool connected but not running.
Refer to Optional Accessories for more information.
Transporting (Fig. 1A)
Transport the machine using the hand indentations (13).
WARNING: Always transport the machine in saw bench mode
with the upper blade guard fitted. Ensure that the upper guard
covers the saw blade completely. Never carry the machine by
the guard.
Basic Saw Cuts
SAWING IN MITRE SAW MODE
It is dangerous to operate without guarding. Guards must be in position
when sawing.
Ensure that workpieces are clamped securely.
VERTICAL STRAIGHT CROSS CUT (FIG. A1, K)
1. Slacken the mitre latch (8) and subsequently squeeze it.
2. Engage the mitre latch (8) at the 0° position and fasten the mitre latch.
3. Place the wood to be cut against the fence (11).
4. Take hold of machine handle and press the head lock-up release lever
(2) to release the head.
5. Pull down the head approximately 10 mm and release the lock-up lever.
6. Switch on the machine and depress the head to allow the blade to cut
through the workpiece and enter the table slot.
7. After completing the cut, switch off the machine and return the head to
its upper rest position.
VERTICAL MITRE CROSS-CUT (FIG. A1, L)
1. Squeeze the mitre latch (8). Move the arm left or right to the required
angle.
2. The mitre latch will automatically locate at 0°, 15°, 22.5°, 45° and 50°
both left and right. If any intermediate angle is required hold the head
firmly and lock by fastening the mitre latch.
3. Always ensure that the mitre latch is locked tightly before cutting.
4. Proceed as for a vertical straight cross-cut.
WARNING: When mitring the end of a piece of wood with a
small off-cut, position the wood to ensure that the off-cut is to
the side of the blade with the greater angle to the fence:
– left mitre, off-cut to the right
– right mitre, off-cut to the left
BEVEL CROSS-CUT (FIG. H1, M)
Bevel angles can be set from 0° to 48° to the left. Bevels up to 45° can
be cut with the mitre arm set between zero and a maximum of 45° mitre
position right or left.
1. Set the bench table to its highest position so that the table does not
interfere with the sliding fence.
2. Loosen the bevel clamp handle (12) and set the bevel as desired.
3. Set the override button (54) if required.
4. Hold the head firmly and do not allow it to fall.
5. Tighten the bevel clamp handle (12) firmly.
6. Proceed as for a vertical straight cross-cut.
Sawing in the Bench Mode
RIPPING (FIG. A2, I1, I2, N)
WARNING: The bench table is not adjustable in horizontal
position when the guard (18) is not mounted.
1. Set the saw head to the vertical position.
2. Loosen locking knob (60) on left side of fence (11) and move fence to
new position as shown (fig. I1).
3. Slide the guard (18) over the rotating table/mitre arm (9) until threads of
head lock down screw align with threaded bushing in head (fig. I2).
4. Depress the head lock up release lever (2) and press down on the head
while tighening the head lock down screw (20).
5. Set the depth of cut by sliding the table (21) up or down. The correct
position is to have the tips of three teeth above the top surface of the
wood.
6. Set the rip fence (17) as required in order to support as much of the
workpiece as possible. At least the rear end of the fence should be level
with the front of the riving knife.
7. Set the rip fence for the width of cut required by using the scale let into
the front of the table.
… 32 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für DeWalt DW711 T 7 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info