Bedienungsanleitung DeWalt DWE314 (Seite 26 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

712355

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISH



CAUTION: To avoid injury, ensure adaptor and accessory

are securelytightened.

Non-

DeWALT

accessories can be attached using the

universaladaptor.

1. Place the washer

11

on thetool.

2. Place accessory on towasher.

3. Tighten and secure adaptor nut

12

using a hexwrench.

Attaching the Cut Guide (Fig. G–L)

The depth/cut guide allows you to precisely cut material at a

specified depth and more accurately track a marked cutline.

1. Attach the cut guide block

6

by inserting the accessory

tabs

13

on the guide into the accessory side mount slots

5

on the main body of thetool.

2. Secure the block to the main body with the supplied screw

assembly

15

. Tighten with the supplied hex key

16

Depth Guide

This feature allows you to precisely cut material at a

specifieddepth.

1. Insert the guide arm

7

as shown in figureH into the front

slot on the guide block

6

2. Adjust the length of the guide by pulling out or pushing

inward to achieve the desired cut depth as shown in figureI.

3. Secure the guide in place by turning the depth/cut

adjustment knob

14

clockwise. To release the guide turn

the depth/cut adjustment knobcounterclockwise.

Cut Guide

This feature allows you to more accurately track a marked

cutline.

1. Insert the guide arm

7

as shown in figureJ into the slots on

the left and right sides of the guide block

6

2. Adjust the length of the guide by pulling out or pushing

inward to achieve the desired length as shown in figureK.

3. Secure the guide in place by turning the depth/cut

adjustment knob

14

clockwise. To release the guide turn

the depth/cut adjustment knobcounterclockwise.

NOTE: The guide arm can also be placed in the guard assembly

vertically in order to set the height off a cut. Refer to figureL.

Attaching the Dust Extraction Adaptor

(Fig. P)

The Dust Extraction Adaptor allows you to connect the tool to

an external dust extractor, either using the AirLock™ system

(DWV9000-XJ), or a standard 35mm dust extractorfitment.

1. Attach the dust extraction adaptor

17

by inserting the

tabs

13

in to the accessory side mount slots

5

2. Insert screw assembly

15

into the dust extraction

adaptor

17

and tighten with the supplied hex key

16

OPERATION

Instructions for Use (Fig. M, N)



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Be sure the

trigger switch is in the OFF position. An accidental start-up

can causeinjury.



WARNING: Ensure switch is fully OFF before plugging in

the powercord.

1. Plug in powercord.

2. To turn the tool ON, hold it as shown in figureM and press

the variable speed trigger

1

NOTE: The further the trigger switch is depressed the faster

the tool will operate. If in doubt about the proper speed

for your operation, test the performance at low speed and

gradually increase until a comfortable speed isfound.

3. To turn the tool OFF, release the variable speed trigger

1

Lock-on Button (Fig. N)

For more comfort in extended use applications, the

lock-on button

4

can lock the trigger trigger

1

in the

depressedposition.

LED Worklight (Fig. O)

The LED worklight

2

will activate when the trigger is depressed

Proper Hand Position (Fig. M)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires the tool to be held as shown in

FigureM.

Using the Dust Extraction Adaptor with the

Sanding Platen (Fig. Q)

1. Attach the dust extraction adaptor

17

. Refer to Attaching

the Dust ExtractionAdaptor.

2. Attach the sanding platen

9

as described under Installing/

RemovingAccessories.

3. Attach sanding sheet as described under Installing/

Removing SandingSheets.

Using the Dust Extraction Adaptor with

Plunge Cutting Accessory (Fig. R)

1. Attach the dust extraction adaptor. Refer to Attaching the

Dust ExtractionAdaptor.

2. Push dust extraction arm

19

into the lower aperture of the

dust extraction adaptor

17

3. Attach plunge cutting bit as described under Installing/

RemovingAccessories.

4. Adjust the dust extraction arm

19

for bestresults.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DWE314 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info