Bedienungsanleitung DeWalt DWE4246 (Seite 42 von 204) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

712331

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

ENGLISH

Setting Guard Adjustment Options

To adjust the guard release lever

9

for desired

adjustmentoption:

1. Remove screw

12

using a T20 bit.

2. Remove the guard release lever taking note of the spring

position. Choose the end of the lever for the desired

adjustment option. One-touch will use the slanted end of

the lever

9

to engage the alignment holes

15

on the guard

collar. Two-touch will use the squaredend to engage the

alignmnet holes

15

on the guard collar.

3. Replace the lever, positioning the chosen end under the

spring

13

. Ensure the lever is in proper contact with

thespring.

4. Replace screw and torque to 2.0-3.0N-m. Ensure proper

installation with spring return function by depressing guard

release lever

9

Mounting Guard (Fig. D)



CAUTION: Prior to mounting guard, ensure the screw,

lever, and spring are fitted correctly before mounting

theguard.

1. With the spindle facing the operator, press and hold the

guard release lever

9

2. Align the lugs

13

on the guard with the slots

14

on the

gearcase.

3. Push the guard down until the guard lugs engage and

rotate them in the groove on the gear case hub. Release the

guard release lever.

4. To position the guard:

One-touch

: Rotate the guard clockwise into the desired

working position. Press and hold the guard release lever

9

release lever to rotate the guard in the anti-clockwise

direction.

Two-touch

: Press and hold the guard release lever

9

Rotate the guard clockwise or anti-clockwise into the

desired working position.

NOTE: The guard body should be positioned between the

spindle and the operator to provide maximum operator

protection.

The guard release lever should snap into one of the

alignment holes

15

on the guard collar. This ensures that

the guard is secure.

5. To remove the guard, follow steps 1–3 of these instructions

in reverse.

Flanges and Wheels

Mounting Non-Hubbed Wheels (Fig. E)



WARNING: Failure to properly seat the flange/ clamp nut/

wheel could result in serious injury (or damage to the tool

or wheel).



CAUTION: Included flanges must be used with depressed

centre Type 27 and Type 42 grinding wheels and Type41

cutting wheels. See the Accessories Chart for more

information.



WARNING: A closed, two-sided cutting wheel guard is

re quired when using cutting wheels.



WARNING: Use of a damaged flange or guard or fail ure

to use proper flange and guard can re sult in injury due to

wheel breakage and wheel contact. See the Accessories

Chart for more information.

1. Place the tool on a table, guard up.

2. Install the unthreaded backing flange

4

on spindle

2

with

the raised centre (pilot) facing the wheel.

3. Place wheel

16

against the backing flange, centreing the

wheel on the raised centre (pilot) of the backing flange.

4. While depressing the spindle lock button and with the

hex depressions facing away from the wheel, thread the

clampnut

5

on spindle so that the lugs engage the two

slots in the spindle.

5. While depressing the spindle lock button, tighten the

clamp nut

5

a. Tighten standard clamp nut using a wrench

20

b. Tighten a keyless clampnut by hand. (Only use a keyless

clampnut if it is in perfect condition.) Refer to Package

Contents to see clampnut details.

6. To remove the wheel, depress the spindle lock button and

loosen the clamp nut.

Mounting Sanding Backing Pads (Fig. F)

NOTE: Use of a guard with sanding discs that use backing pads,

often called fiber resin discs, is not required. Since a guard is

not required for these accessories, the guard may or may not fit

correctly if used.



WARNING: Failure to properly seat the flange/ clamp nut/

wheel could result in serious injury (or damage to the tool

or wheel).



WARNING: Proper guard must be reinstalled for grinding

wheel, cutting wheel, sanding flap disc, wire brush or

wire wheel applications after sanding applications are

complete.

1. Place or appropriately thread backing pad

17

thespindle.

2. Place the sanding disc

18

on the backing pad

17

3. While depressing spindle lock

1

, thread clamp nut

19

spindle, piloting the raised hub on the clamp nut into the

centre of san ding disc and backingpad.

4. Tighten the clamp nut by hand. Then depress the spindle

lock button while turning the sanding disc until the sanding

disc and clamp nut are snug.

5. To remove the wheel, grasp and turn the backing pad and

sanding pad while depressing the spindle lock button.

Mounting and Removing Hubbed Wheels

(Fig. A)

Hubbed wheels install directly on the M14 threaded spindle.

Thread of accessory must match thread of spindle.

1. Remove backing flange by pulling away from tool.

2. Thread the wheel on the spindle

2

by hand.

3. Depress the spindle lock button

1

and use a wrench to

tighten the hub of the wheel.

4. Reverse the above procedure to remove the wheel.

DeWalt DWE4246 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info