Bedienungsanleitung DeWalt DWE4246 (Seite 43 von 204) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

712331

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

ENGLISH

NOTICE: Failure to properly seat the wheel before turning

the tool on may result in damage to the tool or the wheel.

Mounting Wire Cup Brushes and

Wire Wheels (Fig. A)



WARNING: Failure to properly seat the flange/ clamp nut/

wheel could result in serious injury (or damage to the tool

or wheel).



CAUTION: To reduce the risk of personal injury,

wear work gloves when handling wire brushes and

wheels. They can become sharp.



CAUTION: To reduce the risk of damage to the tool,

wheel or brush must not touch guard when mounted

or while in use. Undetectable damage could occur to

the accessory, causing wires to fragment from accessory

wheel or cup.

Wire cup brushes or wire wheels install directly on the threaded

spindle without the use of flanges. Use only wire brushes or

wheels provided with a M14 threaded hub. These accessories

are available at extra cost from your local dealer or authorised

service centre.

1. Place the tool on a table, guard up.

2. Thread the wheel on the spindle by hand.

3. Depress spindle lock button

1

and use a wrench on the

hub of the wire wheel or brush to tighten the wheel.

4. To remove the wheel, reverse the above procedure.

NOTICE: To reduce the risk of damage to the tool, properly

seat the wheel hub before turning the tool on.

Prior to Operation

• Install the guard and appropriate disc or wheel. Do not use

excessively worn discs orwheels.

• Be sure the inner and outer flange are mounted correctly.

Follow the instructions given in the Grinding and Cutting

AccessoryChart.

• Make sure the disc or wheel rotates in the direction of the

arrows on the accessory and thetool.

• Do not use a damaged accessory. Before each use inspect

the accessory such as abrasive wheels for chips and cracks,

backing pad for cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or accessory is dropped,

inspect for damage or install an undamaged accessory. After

inspecting and installing an accessory, position yourself and

bystanders away from the plane of the rotating accessory

and run the power tool at maximum no-load speed for one

minute. Damaged accessories will normally break apart

during this testtime.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Be sure the

trigger switch is in the OFF position. An accidental start-up

can cause injury.



WARNING:

• Ensure all materials to be ground or cut are secured

inplace.

• Secure and support the workpiece. Use clamps or a

vice to hold and support the workpiece to a stable

platform. It is important to clamp and support the

workpiece securely to prevent movement of the

workpiece and loss of control. Movement of the

workpiece or loss of control may create a hazard and

cause personalinjury.

• Support panels or any oversized workpiece

to minimize the risk of wheel pinching and

kickback. Large workpieces tend to sag under their

own weight. Supports must be placed under the

workpiece near the line of cut and near the edge of the

workpiece on both sides of thewheel.

• Always wear regular working gloves while operating

thistool.

• The gear becomes very hot duringuse.

• Apply only a gentle pressure to the tool. Do not exert

side pressure on thedisc.

• Always install the guard and appropriate disc or

wheel. Do not use excessively worn disc or wheel.

• Be sure the inner and outer flange are

mountedcorrectly.

• Make sure the disc or wheel rotates in the direction of

the arrows on the accessory and thetool.

• Avoid overloading. Should the tool become hot, let it

run a few minutes under no load condition to cool the

accessory. Do not touch accessories before they have

cooled. The discs become very hot duringuse.

• Never work with the grinding cup without a suitable

protection guard inplace.

• Do not use the power tool with a cut-offstand.

• Never use blotters together with bonded

abrasiveproducts.

• Be aware, the wheel continues to rotate after the tools

is switchedoff.

Proper Hand Position (Fig. G)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the side handle

3

with the other hand on the body of the tool, as shown in

FigureG.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt DWE4246 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info