Bedienungsanleitung Dik Geurts Vidar Triple-wall (Seite 31 von 76) (Deutsch, Englisch, Holländisch, Französisch)

695365

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

English

INSTALLATION MANUAL

9. Appliance-specific information

!CAUTION

- The appliance-specific instructions as described in this section prevail over the instructions in the other

sections! If in doubt follow the instructions in section 9 or contact your supplier.

- The appliance-specific information as described in paragraphs 9.1 to 9.4 applies to all models described in

this manual. Supplementary installation instructions (per appliance) are described in paragraph 9.5.

9.1 Outside air connection, air slide valve and restrictor slide

9.1.1 Outside air connection

The fire is made with an outside air connection. This outside air connection is supplied separately.

Assembly always takes place at the bottom of the appliance.

When mounting the outside air connection, please proceed as follows (see Annex 2, fig. 3):

Loosen the 5 bolts that are pre-mounted on the outside air connection.

Bring the outside air connection against the plate on the bottom of the appliance.

Then re-tighten the 5 bolts.

Connect the flexible hose (Ø 80 mm) to the round pipe opening of the outside air connection. The flexible hose

can be fed from the back or the bottom.

!Caution

In case of the Vidar Triple, supply via the back of the appliance is possible. For this purpose, the round plate at the

back of the appliance must be pressed out (see Annex 2, fig. 4).

9.1.2 Air slide valve

When installing and maintaining the appliance, please check the operation of the air slide valve

(see Annex 2, fig. 5). It is possible that steel grit entered the air slide valve during transport. If the air slide valve

does not move smoothly it must be cleaned. For this purpose, the air slide valve must be disassembled.

The suspended air slide valve is spring-mounted using a bolt and a spring, which are located below the cover

plate.

When mounting the air slide valve, please proceed as follows (see Annex 2, fig. 5):

Remove the vermiculite plates from the bottom (see section 9.2.1).

Unscrew the cover plate's 6 Allen screws from the bottom.

Remove the cover plate.

Only in case of an outside air connection, unscrew the 2 screws from the front strip and remove it.

Remove the front strip or the outside air connection plus front strip.

Unscrew the Allen screw with spring.

Remove the air slide valve by bringing it towards you.

Check the air slide valve and clean it if necessary.

In order to replace the air slide valve, proceed as described for removal, only in reverse order.

9.1.3 Restrictor slide

The appliance is provided with a restrictor slide (see Annex 2, fig. 6). This will allow you to control the chimney

draught. If the chimney draught is (too) strong, it may be necessary to adjust the restrictor slide. This restrictor

slide is located above the flame baffle plate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dik Geurts Vidar Triple-wall Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dik Geurts Vidar Triple-wall

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info