Bedienungsanleitung Dik Geurts Vidar Triple-wall (Seite 32 von 76) (Deutsch, Englisch, Holländisch, Französisch)

695365

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

English

INSTALLATION MANUAL

9.2 Interior lining

9.2.1 Vermiculite

The fire's vermiculite plates are located on the bottom and against the rear wall of the appliance

(see Annex 2, fig. 7). In the following situations the vermiculite plates must be taken out:

- When disassembling the air slide valve (see section 9.1.2).

- To be able to reach the adjustable legs (see section 9.5).

- When replacing the vermiculite plates.

The bottom plates and the underlying felt are first removed and the rear plates last. The insertion of the

vermiculite plates takes place in reverse order.

!Caution

Make sure that the vermiculite plates are placed back in the original position! The back plate, for instance, must be

placed with the small, not countersunk, holes towards the front.

9.2.2 Flame baffle plate

On delivery the flame baffle plate (see Annex 2, fig. 7) will be lying on the bottom of the appliance.

It must be placed on the accompanying profiles in the top of the appliance.

To do this proceed as follows:

Take the flame baffle plate and tilt it backwards.

!Caution

The stainless steel profile must be placed at the front with the screw heads facing the top (see Annex 2, fig. 7).

Lift the flame baffle plate into the top of the appliance.

Slide the front of the flame baffle plate over the 2 iron supports located at the top, at the front of the appliance

(see Annex 2, fig. 8).

Then slide the flame baffle plate towards the back and centre it in the appliance.

The flame baffle plate is now in the correct place.

The removal of the flame baffle plate takes place in reverse order.

9.3 Door adjustment

Check the closing of the door during installation or maintenance. The door can be adjusted if desired. This will be

the case if sealing is insufficient (gaps).

Check the sealing of the door by placing a sheet of paper between the door and the fire. After closing the door, it

should not be possible to pull out the sheet of paper easily. Check the outside of the fire.

Proceed as follows when adjusting the door:

Loosen the 2 hexagonal bolts on the top and bottom side of the non-hinging part of the door with an open-end

spanner by one turn (see Annex 2, fig. 9).

!Caution

Do not fully remove these bolts!

The door can now be adjusted.

Check whether the door still seals well, using the test with a sheet of paper described above.

Tighten the bolts again.

9.4 Glass panes

!Caution

- Avoid damage when removing/fitting the glass pane.

- Avoid/remove fingerprints on the glass pane(s) as they will burn into the glass.

!Tip

Use the supplied glass pane cleaner to remove fingerprints from the glass pane(s).

9.4.1 Disassembly of glass panes

9.4.1.1 Disassembly of glass pane in door

To remove the glass pane in the door, please follow the instructions below (see Annex 2, fig. 10):

Open the door.

Lift out the door by sliding it upwards.

Place the door on a flat surface.

Remove the door seal.

Unscrew the nuts under the door seal from the glass strip.

Remove the glass strips.

Lift the glass pane out. The pane seal is also taken out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dik Geurts Vidar Triple-wall Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dik Geurts Vidar Triple-wall

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info