Bedienungsanleitung Dik Geurts Vidar Triple-wall (Seite 34 von 76) (Deutsch, Englisch, Holländisch, Französisch)

695365

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

English

INSTALLATION MANUAL

!Tip

Prior to placing the appliance, remove the front door and flame baffle plate in order to avoid damages and ease

installation.

Suspend the appliance over the lip of the wall plate and adjust the fire using the spacers at the back.

Place the flue pipe and possible rosette.

9.5.1.2 Installing a protective plate for the plasterwork

If the appliance is placed against a plastered wall or a wall with light coloured paint/wash, we recommend

installing the supplied protective plate for the plasterwork. Without this plate, the plasterwork or paint/wash can

be damaged due to high temperatures.

Proceed as follows:

Allow the protective plate at the back of the flue duct to rest on the appliance.

Then press the plate against the flue duct.

Drill 4 small holes (Ø 4 mm) and fix the plate using the supplied screws (see Annex 2, fig. 13).

9.5.1.3 Connection of the flue

In case of the Vidar Wall, the flue can be connected in two ways: drained or non-drained. For this you will have to

use the specially developed conical ring. The required connecting pieces are available through your supplier.

9.5.2 Vidar Triple

9.5.2.1 Placing the appliance

In order to promote a stable set-up, the Vidar Triple is provided with two adjustable feet (see Annex 2, fig. 14).

They are located at the front of the casing and can be adjusted.

9.5.2.2 Connection of the flue

In case of the Vidar Triple, the flue can be connected in two ways: drained or non-drained. For this you will have to

use the specially developed conical ring. The required connecting pieces are available through your supplier.

9.5.3 Instyle Triple L

9.5.3.1 Placing the appliance

In order to promote a stable set-up, the Instyle Triple L is provided with adjustable feet (see Annex 2, fig. 15).

These feet can be adjusted by means of the supplied socket screwdriver.

Remove the vermiculite from the bottom.

Turn the socket screwdriver to the right in order to adjust the fire upwards, and to the left to adjust the fire

downwards.

9.5.3.2 Connection of the flue

In case of the Instyle Triple L, it is possible to create a flue without exhaust materials. For this you will have to

create an air-tight connection between the top of the fire and the chimney (see paragraph 5.4.2). In addition, a

drained connecting piece ‘liner kit’ is available in order to achieve a flexible connection.

Proceed as follows:

Pull the flexible pipe through the chimney.

Attach the draining connecting piece ‘liner kit’ using the clip binding on the flexible pipe (see Annex 2, fig. 16).

Push the flexible pipe including connecting piece back in the chimney.

Slide the fire into place.

Remove the flame baffle plate if it is already in the correct place in the top of the appliance (see paragraph 9.2.2).

Insert a hand through the flue hole and grasp the connecting piece.

Pull the flexible pipe with the connecting piece downwards.

Clamp the flexible connecting piece to the appliance by bending the 3 clamp strips (see Annex 2, fig. 17).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dik Geurts Vidar Triple-wall Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dik Geurts Vidar Triple-wall

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info