Bedienungsanleitung Dimplex Toluca DeLuxe (Seite 5 von 8) (Englisch)

706502

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Installation

WARNING: FALLING OR TIPPING APPLIANCES CAN

CAUSE INJURY OR DEATH OF YOUNG CHILDREN, PLEASE

ENSURE CHILDREN DO NOT CLIMB, HANG OR STAND ON

THIS PRODUCT.

WARNING: THE APPLIANCE IS PROVIDED WITH A WALL

FIXING KIT, THIS KIT IS DESIGNED TO HOLD THE PRODUCTS

WEIGHT, IT IS NOT A SUBSTITUTE FOR PROPER ADULT

SUPERVISION. DO NOT ALLOW CHILDREN TO CLIMB OR HANG

ON THIS PRODUCT.

Safety Message - Sufcient expertise is required for installing

this product. If unsure we recommend that you use an

installer and pay special attention to safety during the

installation.

Wall Installation- See Fig. 2

Do not connect appliance until properly xed to the wall

and the Instruction leaet is fully read. In particular, the

minimum distances must be observed.

The wall plugs supplied with this product are for use with

Block/Brick built walls only.

This model is designed to be permanently xed to a wall

at a minimum height of 300mm. The wall bracket must be

tted horizontally and the cable routed to the bottom right

of the appliance.

A height of 600 to 725mm from bottom of the appliance

to oor is recommended for optimum viewing of fuel bed.

For optimum viewing, mark the top three screw xing

positions on the wall in accordance with the recommended

xing dimensions - see Fig. 2. Drill holes with a 6mm drill bit.

Fix the wall bracket using the plugs and screws provided.

Carefully lift the appliance up ensuring that the appliance

engages with the wall bracket correctly.

A bottom xing bracket is supplied with the unit, xed to

the base of the appliance. Remove the screw and the

bracket, turn the bracket through 180 degrees so it is now

facing downward and re t using the screw just removed.

With the bracket in place mark the location of the hole on

the wall. Remove the appliance,drill the wall, t the wall

plug and re-t the appliance ensuring that you secure it in

place by screwing the bottom xing bracket to the wall.

Remote Control - See Fig. 3

maximum range of use is ~ 5metres.

NOTE: It takes time for the receiver to respond to the transmitter.

NOTE: The reciever for the remote control is located in the

display, aim the remote control in this direction when inputting

commands.

Do not press the buttons more than once within two seconds

for correct operation.

Battery Information - See Fig. 3

1. To activate the remote control remove the clear battery

isolation strip at the base of the remote control, which is used

to ensure your remote control reaches you fully charged.

2. To replace the remote control battery, turn over the remote

control, and follow the diagram embossed on the remote

control

3. Only use CR2025 or CR2032 size of batteries.

Wireless Speaker Control.

The unit needs to be in standby for the speaker function to

operate, you do not need the ame effect to be operating.

The speaker can be used in 2 ways. You can pair a suitable

device to the speaker wirelessly and listen to music, audio

books or casts from a suitable device, or when the ame

effect is operating the soothing crackling sound of a log re

can be played for ambient sound effect.

To listen to the crackling log effect, just press the volume up

button on your remote control until you reach a vlolume

level which is comfortable for you, to lower the volume press

the volume down button. The crackling is turned OFF by

pressing the volume down button until the sound is muted.

To use the speaker to listen to your own material the speaker

must rst be paired to a compatible device. To pair with the

unit:

1. Ensure the unit is plugged in and switched on at the mains

socket.

2. Using a compatible device search for “DImplex Fire”,

select and pair your device to “DImplex Fire”.

3. Once connection is made between your device and the

unit an electronic tone will sound to alert you the pairing

was successful.

With the unit now paired you can control the speaker

volume using the volume buttons on the remote control

handset or your device’s volume controls.

Note: If you experience problems pairing to the speaker,

you may need to re-pair to the speaker, follow these steps:

1. On your device go to the Bluetooth Settings.

2. Select the “Dimplex Fire” and press “Forget” to disconnect

from the speaker.

3. Turn Bluetooth OFF, and then ON. Your device should now

rediscover “Dimplex Fire” again.

4. Select “Dimplex Fire” to pair with the speaker.

User Modes:

Mode Name /Discription Action (Actions cannot be input by remote control)

Change Celsius (

C) to Fahrenheit (

Press both Temp Up ( ) and Temp Down ( ) on the unit and hold until beep is heard

and display flashes. (To revert back to Celsius repeat this action)

Disable/Enable Heat Options

Hold both Back Light ( ) and Temp Down ( ), on the unit, for 2 seconds, when the

heater has been disabled the display will read “--” and beep. To enble heat repeat this

action.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dimplex Toluca DeLuxe Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info