Bedienungsanleitung Dirt Devil m 5050 infitnity vx 8 (Seite 15 von 24) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Türkisch)

318503

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

5 Maintenance

5.3 Cleaning the particle trap

1. Switch off the appliance, Zchapter 4.3, „Switching off“

2. Remove the dust container Zchapter 5.1, „Emptying and cleaning the

dust container“.

3. If dirt is visible in the suction channel (Fig. 13/A1), lay the appliance on

its side.

4. Open the particle trap by twisting it off (Fig. 13/B). The dirt will fall out

of the opening. If necessary, help a bit by hand.

5. Empty the dirt into a dustbin.

6. Close the cleaned suction channel by refitting and fastening the particle

trap.

7. If you haven't done this by now, firmly push the dust container back into

its receptacle. Check that it is securely fitted..

5.4 Cleaning the hygienic exhaust filter

1. Switch off the appliance, Zchapter 4.3, „Switching off“

2. Push the release catch of the exhaust filter cover down (Fig. 14/A) and

fold down the exhaust filter cover.

3. Remove the exhaust filter (Fig. 14/B).

4. Tap the exhaust filter over a dustbin for a rough cleaning. Remove larg-

er agglomerations of dirt by hand.

5. Remove residual dust with a soft brush, e.g. the supplied furniture

brush.

6. Ifthe filter is damaged or deformed, replace it.(ordering information

Zchapter 5.5, „Spare parts and accessories“).

7. Place the clean/new exhaust filter back into its fitting.

8. Attach the exhaust filter cover at the bottom side first and then fold it

upwards.

5.5 Spare parts and accessories

 Ordering address: Zpage 48, „International Service“.

 Further information: Z www.dirtdevil.de

 The following accessories and spare parts can be reordered:

5.6 Before you send in the appliance

Before contacting your authorised Royal dealer, Royal service partner or

appliance market or sending in the appliance, first follow the procedure in

the following table to check if you can solve the problem yourself.

ATTENTION:

Only use original spare parts from the scope of delivery or those that you

have acquired by reordering.

Item number Description

5050001 1 Dual motor protection filter (2 pieces: foam plastic filter

element (Fig. 1/19) and filter holder (Fig. 1/20))

5050002 1 hygienic exhaust filter

5050003 1 particle trap Item number Description

M203 1 parquet brush M219 1 mini turbo brush

M209 1 turbo brush M232 1 long crevice nozzle

WARNING:

Danger of injury! Never use a defective appliance! Always switch off the

appliance and disconnect it from the mains before starting troubleshoot-

ing Zchapter 4.3, „Switching off“.

Problem Solution

The appli-

ance will

not start

The socket does not carry current.

Test the vacuum cleaner at another socket which you are

sure carries current.

Power cord is damaged. Have the power cord replaced by

Royal Appliance Customer Service, address, Zpage 48,

„International Service“.

The vacu-

um cleaner

stops sud-

denly.

The overheating protection has tripped (possibly due to

blocked suction channels, filters, or similar).

Switch the appliance off and pull the plug out of the socket.

Remove the cause of overheating (e. g. by disassembling

telescopic tube and suction hose and removing the obstacle

and/or cleaning filters). Wait for about 45 minutes. After the

appliance has cooled off, you may switch it on again.

Cleaning

indicator

(Fig. 1/13,

optional)

lights up.

The dust container is full.

Empty / clean the dust container, Zchapter 5.1, „Emptying

and cleaning the dust container“ and Zchapter 5.3, „Clean-

ing the particle trap“

The clean-

ing results

are unsat-

isfactory in

spite of the

appliance

working

correctly.

The bypass vent (Fig. 1/24) is open.

Close the bypass vent (Fig. 1/24).

The attached nozzle is unsuitable.

Change the nozzle Zchapter 3.2, „Selecting the proper noz-

zle“

The position of the "carpet/hard floor" selector (Fig. 1/28) is

unsuitable.

Set the "carpet/hard floor" selector (Fig. 1/28) to the correct

position for the type of floor, Zchapter 4.2, „Vacuum clean-

ing“, step 4.

The dust container is full.

Empty / clean the dust container Zchapter 5.1, „Emptying

and cleaning the dust container“.

The filter is dirty.

Change/clean the respective filter Zchapter 5.2, „Cleaning

the cyclone unit and the dual motor protection filter“ or

Zchapter 5.4, „Cleaning the hygienic exhaust filter“.

Nozzle, telescopic tube or suction hose are blocked.

Remove the obstacle. If necessary, use a long wooden stick

(e.g. a broomstick) to do this.

Problem Solution

Infinity Excell.book Seite 15 Dienstag, 1. März 2011 9:33 09

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dirt Devil m 5050 infitnity vx 8 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info