Bedienungsanleitung DRU Cosmo Tunnel (Seite 5 von 40) (Englisch)

810284

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

INSTALLATION MANUAL

3.4 Principle of ignition cycle

Below you will find a brief description of how this appliance is ignited. The receiver in the appliance will get a

signal from the remote control to start the ignition process. The receiver will get the signal to start the ignition

process. This signal is passed on to the burner device, after which, if applicable, the relay for the Powervent

System® is switched. After an 8 second interval, the ignition on the spark electrodes will start. If no Powervent

System® is connected, only the relay will switch and the ignition will start immediately. The main burner will be

ignited at about 50% of its capacity. This will prevent a larger amount of gas in the combustion chamber, if no

ignition takes place. When the gas ignites, ionization will have to be detected. In order to make sure the flame has

passed over, this will take place at the other side of the burner. When ionization is detected, the gas control will

modulate to 100%.

In case of an appliance with a switchable second burner, the second valve is switched (you will be able to hear a

'click') in order to ignite the second burner. After ignition of the second burner, the appliance will always go to the

full position (full capacity). This will guarantee that the second burner will actually ignite. The second burner can

be switched on and off manually, by means of the remote control. In case of switching on manually, the appliance

will first return to full load.

!Caution

The appliance's control unit is characterized by stringent safety requirements. It is possible that the burning

appliance switches off automatically and then switches back on again. This is not a failure, but a check.

The moment the appliance's control unit is connected to mains voltage, the control unit will perform this check

every 24 hours. If the appliance is burning at that time, the appliance will extinguish and then start again

immediately.

If you wish to prevent this, you can remove the plug and insert it again at a time during the 24 hours when the

appliance is never or hardly ever burning.

4. Removing the packaging

Note the following items when removing the packaging:

Remove all packaging materials.

Remove all supplied components in, on and/or at the appliance.

Check the appliance and accessories for damages (during transport).

If necessary, contact your supplier.

Never install if an appliance is damaged!

Remove any screws that are used to fix the appliance to a platform or pallet.

!Caution

The glass pane(s) is/are made of a ceramic material. Very small irregularities in the glass panes cannot be avoided,

but are within the required quality standards.

!Caution

Keep plastic bags away from children.

Appendix 2, table 1 indicates which components should be available after unpackaging.

Contact the supplier if you find that not all components have been supplied.

Packaging must be disposed of in accordance with the regulations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU Cosmo Tunnel Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU Cosmo Tunnel

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info