Bedienungsanleitung DRU Cosmo Tunnel (Seite 7 von 40) (Englisch)

810284

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

INSTALLATION MANUAL

!Caution

When installing a built-in appliance, always take the following into account:

• The minimum construction measurements according to Appendix 3, Fig. 1 and 2.

• The construction height of the appliance.

Provide a gas connection at the location. For details, see section 5.2.

Make a passage for the concentric system; for details, see section 5.8.3.

!Caution

Additional instructions for the appliance to be installed can be found from section 5.10.

5.5 Placing a built-in appliance (if applicable)

Not all built in DRU appliances are supplied with a control hatch.

!Caution

Built in appliances must be installed with the DRU control hatch. This is necessary to ensure a durable, safe and

proper operation. The DRU control hatch can be ordered separately. Exceptions are:

Appliances with supplied DRU guard cabinet. The DRU guard cabinet is intended for installation with a suspended

platform. If the appliance will be connected to the DRU PowerVent system, the DRU control hatch has to be used

after all.

The gas control is mounted to the appliance. It must be taken out and placed in the control hatch at a later time.

For placing the gas control in the control hatch, see section 5.7.

Proceed as follows:

Loosen the bracket with the gas control by loosening the self-tapping screws and screw the self-tapping screws

back in the appliance.

Place the bracket with gas control, together with the wiring of the ignition/ionisation cable(s), the flexible gas

hose(s) and type plate with chain in the direction of the control hatch.

!Caution

The data plate should remain connected to the chain.

Set the height of the appliance using the adjustable feet.

Make the appliance level at the same time.

!Tip

The construction frame can be adjusted afterwards for most 2- or 3 sided appliances. This allows a good contact of

the construction frame with the chimney breast. Adjustment should take place before the appliance is built in.

After building in, adjustment is no longer possible. For 2- or 3-sided appliances that cannot be adjusted, we refer

to section 5.10 'Additional instructions'.

!Caution

Do not ignite the appliance before the gas, discharge and electric connections have been fully installed, first

observe the procedure described in chapter 7.3.

5.6 Placing the chimney breast (if applicable)

For a good heat discharge and operation of the appliance, there should be sufficient space around the appliance.

The chimney breast should be ventilated sufficiently by means of ventilation holes (incoming and outgoing).

!Caution

When an appliance is built in the floor, please take into account the minimum distances from a combustible

floor. If applicable, additional information about this is provided from section 5.10 'Additional instructions'.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU Cosmo Tunnel Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU Cosmo Tunnel

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info