Bedienungsanleitung DRU Cosmo Tunnel (Seite 15 von 40) (Englisch)

810284

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

INSTALLATION MANUAL

5.14 Placing the wood set

The appliance is supplied with a wood set.

!Caution

• The figures do not always show the correct colours.

• Before placing the wood set in a Cosmo Tunnel RCH, first determine what is the front of the appliance. Make

sure the positions of the burners are exactly the same as indicated in figure 18 in appendix 3.

!Caution

Strictly observe the following instructions to prevent unsafe situations.

Only ever use the supplied wood set.

Place the wood set exactly as described.

Make sure the ionization pin and spark electrode and the surrounding space remain free

(see appendix 3, fig. 13 and 14).

Make sure the slot between the burner and the vermiculite tray is kept free from objects.

Make sure there is no vermiculite's dust on the burner.

5.14.1 Wood set

The wood set consists of vermiculite (see appendix 3, fig. 15), chips (see appendix 3, fig. 16) and a number of logs

(see appendix 3, fig. 17).

Fill the burners with vermiculite; evenly spread the vermiculite (see appendix 3, fig. 18). The vermiculite may not

get higher than the edge of the burners.

!Caution

You can influence the flame picture by moving the vermiculite, but the burner deck should remain covered with

vermiculite in order to avoid reducing the burner's life span.

Check whether the insulating rope around the 2 central burners has been applied correctly

(see appendix 3, fig. 18).

Check whether the ends of the insulating rope around the 2 central burners connect to each other

(see appendix 3, fig. 18).

Identify logs A to H (see appendix 3, fig. 17).

!Tip

Use the burn stains on the logs for identification.

Place logs A and B, using the positioning cams (see appendix 3, fig. 19 and 20).

Place log C, using the positioning pins (see appendix 3, fig. 21).

Continue with central log D (see appendix 3, fig. 22).

!Caution

• Always place central log D with 2 people, to prevent breakage;

• make sure that the space surrounding the central burners is distributed evenly, so that it is possible for

secondary air to flow around the burners;

• make sure the insulating rope around the central burners properly connects to log D.

!Tip

Check the sealing by lighting it from below using a torch.

Then place the cap on the left central burner. This cap will make sure that the flame will transfer smoothly

(see appendix 3. 23).

Place log E (see appendix 3, fig. 24).

Fill the vermiculite tray with chips; spread the chips evenly (see appendix 3, fig. 25).

Identify logs F to H (see appendix 3, fig. 26).

!Caution

The logs may not completely cover the burner pattern (see appendix 3, fig. 27), because:

• the main burner will not ignite properly; which could result in unsafe situations;

• the appliance will become filthy more quickly, as a result of soot;

• the flame picture will be affected.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU Cosmo Tunnel Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU Cosmo Tunnel

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info