Bedienungsanleitung DRU Cosmo Tunnel (Seite 17 von 40) (Englisch)

810284

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

INSTALLATION MANUAL

!Caution

The yellow wire is the + pole, the black wire is the - pole. Always connect ‘- to -‘ and ‘+ to +’ .

6.2.2 Wireless

The wireless connection is divided into 2 types:

• Connection via a ‘modbus’ protocol.

• Control via an application.

!Caution

Only 1 type of wireless connection is possible on the communication module.

6.2.2.1 Connection via ‘modbus’ protocol

Wireless connection of a Domotics system to the receiver is possible via a connection according to the ‘modbus’

protocol. Such a connection can only be established with a communication module (see Appendix 3, fig. 35 (W)).

This module can be ordered from DRU. This communication module translates the ‘modbus’ protocol from the

Domotics system into a wireless signal to the receiver.

When connecting a Domotics system via the communication module to the receiver, proceed as follows:

Use the remote control to test whether the location where the communication module will be placed is within the

reach of the receiver.

Place the remote control on this location and test the reception sensitivity (RSSI).

Press the on/off button and down arrow at the same time. The value that is now visible, must be between -20 and

-70 (see User Manual, "Reception Sensitivity"). If needed, hold the remote control closer to the appliance in order

to improve the reception.

Connect the communication module by means of an RJ45 plug, according to the instructions in the manual that is

supplied with this module.

Now follow the steps described in the ‘modbus’ protocol manual. It is available from the supplier of the domotics

system.

6.2.2.2 Control via application

Also when operating the appliance via a tablet provided with the DRU Control App (iOS or Android), you will need

a communication module. This module can be ordered from DRU.

In order to control the fire via an application, proceed as follows:

Using the remote control, test whether the location where you want to place the communication module is within

the receiver's range.

Place the remote control on this location and test the reception sensitivity (RSSI).

Press the on/off button and down arrow at the same time. The value that is now visible, must be between -20 and

-70 (see User Manual, "Reception Sensitivity"). If needed, hold the remote control closer to the appliance in order

to improve the reception.

Connect the communication module by means of an RJ45 plug, according to the instructions in the manual that is

supplied with the communication module.

Use the instructions for the application in order to install it.

!Caution

• The DRU Control app functions in accordance with the multicast and communication protocol. Ensure the

router is equipped with this. For this, consult the router's installation manual.

• If the DRU Control app is used, the thermostat function no longer applies.

The application 'DRU Control' is available in the AppStore, at GooglePlay or our website: www.drufire.com.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU Cosmo Tunnel Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU Cosmo Tunnel

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info