Bedienungsanleitung DRU Cosmo Tunnel (Seite 18 von 40) (Englisch)

810284

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

INSTALLATION MANUAL

7. Final inspection

In order to check whether the appliance is working properly and safely, you must perform the following

inspections before the appliance is put into operation.

7.1 Gastightness

!Caution

All connections must be gastight. Check the connections for gastightness.

The gas control may be subjected to a maximum pressure of 50 mbar.

7.2 Gas pressure/line-pressure

The burner pressure is set at the factory; see data plate.

!Caution

The line-pressure in house installations must be checked, because it can be wrong.

Check the line-pressure; see Appendix 3, Fig 38 (P1) for the measuring nipple on the gas control.

• Contact the gas company if the line-pressure is too high.

• If the line-pressure is too low, check this at the gas meter. Contact the gas company if the line-pressure is also

too low at the gas meter.

7.3 Ignition main burner

For igniting the main burner, see the User Manual.

7.3.1 First ignition of the appliance after installation or adjustments.

!Caution

After installation, or after work has been performed, you should ignite the appliance for the first time without the

glass window. If necessary, bleed the gas pipe.

Follow the procedure described below:

If necessary, remove the glass pane.

Start the ignition procedure as described in the user manual.

If the main burner does not ignite:

• Reset the system by pressing the buttons ‘arrow up’ and ‘arrow down’ simultaneously.

• Repeat the ignition procedure until the main burner ignites;

!Caution

After each attempt to ignite, the system should be reset by means of the remote control.

Consult the diagram with error messages (Appendix 1) if this does not succeed after a few attempts;

The appliance ignites at 50%. After ionization has been detected, the appliance will modulate to 100%.

This detection will have to take place within 15 seconds, or else the appliance will enter error mode.

If applicable, the second valve will switch to ignite the second burner. Here, you can hear a clear ‘click’ sound.

Check whether the main burner continues to burn.

If the main burner does not continue to burn:

Reset the system as described and repeat the ignition procedure until the main burner continuous to burn.

!Caution

The system can be reset and re-ignited two times in a row at maximum. Then the system will enter a hard lock-out

and you will have to wait half an hour, before you can make a new attempt. Never use more than 3 attempts to

ignite the appliance, as this could lead to a accumulation of gas within the appliance. Make sure that there is no

more gas in the appliance before making 3 new ignition attempts.

Consult the malfunction search diagram (Appendix 1) if this does not happen after a few attempts.

Switch off the appliance.

Clean the glass pane before using it for the first time, as described in the user manual.

Then mount the glass pane as described in section 5.10.

Repeat the ignition procedure a few times and perform the checks described in chapter 7.3.2.

From now on, the main burner should ignite smoothly.

Clean the glass pane after burning for the first time, as described in the user manual.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU Cosmo Tunnel Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU Cosmo Tunnel

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info