Bedienungsanleitung DRU GLOBAL 100 BF (Seite 36 von 64) (Holländisch)

571711

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

INSTALLATION MANUAL

!Caution Some heat-resistant insulation materials

contain volatile components that will

spread an unpleasant smell for a prolon-

ged time; these are not suitable.

Place the concentric system as follows:

• Build the system up from (the connection stump of)

the appliance.

• Connect the concentric pipe pieces and, if necessary,

the bends.

• On each connection, apply a clip binding with silicon

sealing ring.

• Use a self-tapping screw to ﬁ x the clip binding to the pipe

on locations that cannot be reached after installation.

• Apply sufﬁ cient clamps, so that the weight of the pipes

does not rest on the appliance.

• Determine the remaining length of the roof terminal.

• Make sure the roof terminal has the right dimensions.

!Caution Make sure that the right insertion length

is maintained.

• Connect the roof terminal to the concentric pipes.

!Caution - Make sure that the universal tile ﬁ ts well

with the surrounding tiles;

- Make sure that the adhesive plate ﬁ ts well

onto the ﬂ at roof.

6.5.4 Connection of existing chimney

It is possible to connect the appliance to an existing

channel.

A ﬂ exible SS pipe is placed in the chimney for discharging

ﬂ ue gases. The surrounding space is used to supply

combustion air.

The following requirements apply when connecting to an

existing chimney:

- only allowed when used in combination with the special

DRU chimney kit. The installation manual is also supplied;

- the dimensions should be at least 150 x 150 mm;

- the vertical length has a maximum of 12 meters;

- the horizontal length has a maximum of 3 meters;

- the existing chimney has to be clean;

- the existing chimney has to be tight.

If the appliance is installed into an existing chimney by

means of a chimney kit, there may be a slight loss in heat

output.

For setting the appliance, the same conditions/instructions

apply as for the concentric system described above.

6.6 Placing the chimney breast

The appliance is designed to be mounted tightly in a new

chimney breast.

In order to provide proper heat discharge, there should be

sufﬁ cient space around the appliance.

The chimney breast should be ventilated sufﬁ ciently by

means of ventilation holes.

- Use non combustible and heat-resistant

materials for the chimney breast, inclu-

ding the top of the chimney breast, the

material in the chimney breast and the

back wall of the chimney breast;

- Make sure that the appliance is not car-

rying the weight of the chimney breast

when using stone-like materials;

- The ventilation holes – which should be

mounted as high as possible – should have

a combined passage of at least 200 cm

!Caution When placing the chimney breast, you

should take the following into account

(see ﬁ g. 2a and ﬁ g. 2b):

- the location of the control box (K): it

should be placed with a distance of

850 mm to the left or to the right of the

appliance – as low as possible;

- the measurements of the control box; see

Placing the Control Box section 6.7;

- the location of the ventilation holes (V);

- measurement of the pane, so it can be

placed/removed after placing the chimney

breast;

- the protection of the gas control and the

pipes against cement and plaster.

!Tip You should preferably apply the ventila-

tion holes on both sides of the chimney

breast. You can use DRU ventilation

elements.

• Check whether the concentric system is placed correctly.

• Check the ﬁ xture of the clip binding with self-tapping

screws on places that cannot be reached later on.

• Maintain sufﬁ cient space around the appliance in the chim-

ney breast, so the heat can escape:

- minimum internal height: 1350 mm;

- minimum internal width: 1450 mm.

• Do not apply plaster on or over the ﬂ anges (see ﬁ g. 2a

and ﬁ g. 2b, maximum plaster line M), because:

- the heat of the appliance could cause cracks;

- it will no longer be possible to remove/place the pane.

• When using stone-like materials and/or plaster ﬁ nishing,

the chimney breast should dry for at least 6 weeks before

it is taken into operation, in order to prevent cracks.

6.7 Placing the control box

The control box (K) is placed as low as possible in the

chimney breast (see ﬁ g. 2a and ﬁ g. 2b).

!Caution The bottom of the control box may not

be placed higher in the appliance, than the

burner bed.

A number of components are placed in the control box,

such as data plate, gas control, receiver belonging to the

remote control.

Caution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU GLOBAL 100 BF Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU GLOBAL 100 BF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info