Bedienungsanleitung DRU GLOBAL 100 BF (Seite 38 von 64) (Holländisch)

571711

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

INSTALLATION MANUAL

!Tip Use the burn stains on the logs for identi-

ﬁ cation.

Place branches A up to D around the (main) burner

(see Fig. 13b):

Then place branches E up to H that are lying over the bur-

ner (see Fig. 13c,13d).

!Caution The branches should not completely cover

the burner surface,

because:

• the main burner will not ingnite properly;

which could result in unsafe situations;

• the appliance will become ﬁ lthy more

quickly, as a result of soot;

• the ﬂ ame image may be affected.

• Fill the tray surrounding the burner with chips; equally

spread the chips; see ﬁ g. 13e.

6.9.2 Pebble set

The pebble set consists of natural colour vermiculite and

white carrara stones.

• Fill the burner tray with vermiculite; equally spread the

vermiculite.

!Caution - You can inﬂ uence the ﬂ ame image by

moving the vermiculite, yet

- The burner surface must remain covered

with vermiculite in order to prevent that

the life span of the burner is reduced.

• Fill the burner tray and the tray surrounding the burner

with carrara stones;

• Equally spread the carrara stones in one layer;

(see Fig. 13f).

6.10. Pane

After placing the wood set you can place the pane, as

described below.

!Caution - Avoid damages when removing/placing

the pane;

- Use the socket spanner supplied for loo-

sening/tightening the self-tapping screws.

6.10.1 Removing the pane

Remove the pane in accordance with the following instruc-

tions (see ﬁ g. 14a up to 14n):

• Remove the vertical decorative strip at the left and right

side by pushing the strip upwards with a screwdriver,

tilting the strip parallel to the pane and then removing it.

• Remove the self-tapping screw (used for fastening the

pane) from the right glass strip.

• Unscrew the 6 self-tapping screws from the upper glass

strip.

• Remove the upper glass strip.

• Unscrew the self-tapping screw of the wedge at the left

and right side with 2 strokes.

!Caution Do not fully remove the self-tapping

screw, but let it remain in the wedge.

• Push the wedge (left and right) as far upwards as possible.

• Then retighten the self-tapping screws.

• Take hold of the handles and pull the pane towards you.

• Slide the pane as far to the left as possible.

• Tilt the pane towards you by using the right handle and

remove the pane.

6.10.2 Placing the pane

The pane is ﬁ tted by using the above procedure, in reverse

order.

!Caution - Avoid/remove ﬁ ngerprints on the pane,

since otherwise they will burn into the

surface;

- The self-tapping screws must not be

over-tightened, since otherwise they could

break or strip the thread: tight=tight;

- When tightening, push the wedge down-

ward.

7. Wireless remote control

The appliance is supplied with a wireless remote control.

Ignition, controlling the ﬂ ame height and switching off are

performed by a remote control that operates a receiver in

the control box.

User Manual, chapter 4, Wireless Remote Control,

describes the operation of the appliance including the way

the remote control works.

Do not ignite the appliance until it is fully

installed.

Below, we will describe how the receiver is connected.

7.1 Receiver

The receiver should be connected to the appliance, before the

batteries are installed.

Follow the procedure below (see ﬁ g. 15):

• Fit the connection cable’s brown plug to the receiver

(see ﬁ g. 15, arrow F).

• Connect the white plug to the gas control.

!Tip The plugs have different sizes that

correspond with the connectors.

• Connect the cables of thermocouple 1 to the receiver;

(see ﬁ g. 15, arrows B).

!Tip - The size of the eye corresponds with the

size of the screw;

- The colours of eye and screw also

correspond.

• Connect the black wire with the white plug of

thermocouple 2 to the receiver (see ﬁ g. 15, arrow E).

Caution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU GLOBAL 100 BF Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU GLOBAL 100 BF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info