Bedienungsanleitung DRU GLOBAL 100 BF (Seite 39 von 64) (Holländisch)

571711

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

English

INSTALLATION MANUAL

Global 100 BF

!Caution - Make sure that the wires of

thermocouple 2 cannot come into contact

with hot parts;

- Make sure the ignition cable cannot come

into contact with other wires.

• Connect the ignition cable to the receiver;

(see ﬁ g. 15, arrow A).

• Connect power:

a) When using batteries, see section 7.1.1 below;

b) When using an adapter:

- connect it to the receiver; (see ﬁ g. 15, arrow C);

- insert the plug into the wall socket.

• Place the receiver (V) in the control box, as indicated on

ﬁ g. 16.

• Bend the antenna out of the clips; see ﬁ g. 15, arrow D.

• Set the antenna straight.

!Caution - Do not place the antenna (N) too close to

the ignition cable and/or metal parts (for

the correct position, see ﬁ g. 16);

- Do not place the ignition cable over and/or

along metal parts: this will weaken the spark;

- Do not lay the ignition cable over the recei-

ver: this could damage the receiver;

- Avoid dust on or in the receiver: cover it

when performing work.

7.1.1 Placing / replacing the batteries

Follow the procedure below when placing the batteries:

• Open the door of the control box.

• Pick up the receiver.

• Slide the cover off.

• Place or remove the 4 penlite (AA type) batteries.

!Caution - Avoid a short circuit between the

batteries and metal objects/parts;

- Observe the “+” and “-” poles of the

batteries and the holder;

- Use alkaline batteries.

• Slide back the cover.

• Place back the receiver.

!Caution Batteries are regarded as “small chemical

waste” and may therefore not be dis-

posed with the household rubbish.

8. Final check

In order to check whether the appliance is working pro-

perly and safely, you must perform the following checks

before the appliance is used.

8.1 All connections must be gastight.

All connections must be gastight.

!Caution The gas control can be subjected to a

maximum pressure of 50 mbar.

• Check the connections for gastightness

8.2 Gas pressure / pre-pressure

The burner pressure is set at the factory; see data plate. It

is not necessary to check the burner pressure.

The pre-pressure in house installations

should be checked, as they can vary.

• Check the pre-pressure; see ﬁ g. 17 for the measuring nipple

on the gas control.

• Contact the gas company if the pre-pressure is not correct.

8.3 Ignition pilot and main burner

For igniting the pilot and main burners, see the

User Manual, chapter 4, section 4.2, Remote Control.

- During the ignition process, you are not

allowed to operate control button B on

the gas control manually;

- Always wait 5 minutes after the pilot

burner has gone out, before you re-ignite

the appliance.

- Do not turn the pilot burner lower by

using the settings on the gas control.

8.3.1 Pilot burner

• Check the ignition of the pilot burner:

- the pilot burner should start at the ﬁ rst attempt.

If the pilot burner does not ignite:

• check if the ignition sparks:

a) If not, the ignition cable is probably not lying free from

metal parts;

b) If it does, there is probably still air in the pipe.

• Bleed the pipe and/or

• Lay the ignition cable free from metal parts.

8.3.2 Main burner

The burner should ignite smoothly and

should not pop as a result of delayed

ignition.

• Check the function of the main burner from the standby

(pilot burner) position:

- after opening the gas valve, the main burner should burn

within a few seconds.

!Tip When the gas valve is opened, the motor

will run; this is audible.

1) If the main burner does not burn:

• Check if button A on the gas control is in the position ON;

• Check if the space surrounding the pilot burner is free

from objects;

• Check the placement of the wood set.

• If necessary, correct the above mentioned faults.

• Test the main burner 5x for a good operation.

2) If the main burner ignites, but goes out again after

approx. 22 seconds, please:

Caution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU GLOBAL 100 BF Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU GLOBAL 100 BF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info