Bedienungsanleitung DRU Lugo 80 (Seite 14 von 44) (Englisch)

571624

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

English

INSTALLATION MANUAL

5.14.2 Removing the side glass pane

The side glass panes should be removed in case of torn or broken panes:

Remove the front glass pane; see section 5.14.1;

Remove the screws from the vermiculite tray and remove it;

Loosen the nuts of the bottom glass strip on the inside of the appliance by a few turns;

Unscrew the allen bolt from the vertical decorative strip;

Grab the vertical decorative strip at the top, tilt the vertical decorative strip and remove it;

Unscrew the self-tapping screws from the vertical glass strip and remove the vertical glass strip;

Unscrew the self-tapping screws from the upper glass strip and remove the upper glass strip;

Grab the pane at the side and slightly tilt the top towards you;

Lift the glass pane and move it towards the side (you are now located at the side of the appliance);

Tilt the bottom of the glass pane towards the front and remove the glass pane.

5.14.3 Placing the glass pane

Placing the glass pane will take place in reverse order of removing the glass pane, as described above:

!Caution

• Avoid/remove finger prints on the glass pane, as they will burn into the glass;

• The self-tapping screws should not be over-tightened, since otherwise they could break or strip the thread;

• Place the glass pane with the logo at the bottom right.

!Caution

Make sure the front glass pane makes full contact with the side pane (there may be no opening between the side

pane and front pane).

If the front and side glass panes do not connect:

Loosen the self-tapping screws of the side pane clamp strips by a few turns;

Slide the side pane tightly against the front pane;

!Caution

Make sure there is no sealing tape between the front and side panes (where the panes connect).

Tighten the self-tapping screws and nuts of the clamp strips.

5.15 Setting the appliance

The appliance has to be set in such a way that it works correctly in combination with the used concentric system.

For that purpose, a restrictor slide is placed and/or the air inlet guide is removed. The conditions for application

with wall terminal and roof terminal are stated in appendix 2, tables 4, 5 and 6.

This appliance is suitable for PowerVent®. For more information, see the PowerVent® installation manual.

5.15.1 Restrictor slide (R)

The restrictor slide (R) is supplied separately.

It is mounted as follows (see appendix 3, fig. 8):

Unscrew the 2 pre-mounted self-tapping screws (U) from the appliance;

Place the restrictor slide (R) with the 2 self-tapping screws (U). The restrictor slide (R) falls over part of the exhaust

pipe hole, do not tighten the self-tapping screws (U);

!Caution

When fastening, the arrow on the restrictor slide should point away from you.

Adjust the position of the restrictor slide (R) using situations B to E in appendix 2, table 6. The letter for the

restrictor slide position corresponds with the letter of the situation in table 6;

Make sure the point of the triangle belonging to the position that you want and the centre of the self-tapping

screw are exactly aligned;

Tighten the 2 self-tapping screws (U).

5.15.2 Air inlet guide (L)

At the back of the appliance, below the vermiculite tray, the air inlet guide (L) is placed. The air inlet guide can be

reached by removing the vermiculite tray. At delivery, the air inlet guide is placed. When removing the air inlet

guide, proceed as follows (see appendix 3, fig. 9):

Unscrew the self-tapping screws from the vermiculite tray (B) and remove the tray;

Remove the self-tapping screws from air inlet guide and remove the air inlet guide from the appliance.

!Caution

Place back the self-tapping screws back in the appliance.

Place back the vermiculite tray (B) and fasten the tray with the self-tapping screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU Lugo 80 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU Lugo 80

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info