Bedienungsanleitung DRU Lugo 80 (Seite 15 von 44) (Englisch)

571624

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

English

INSTALLATION MANUAL

5.16 Wood set

The appliance is supplied with a wood set.

!Caution

Strictly observe the following instructions to prevent unsafe situations:

Only ever use the supplied wood set;

Only use the glow material (see appendix 3, fig. 14) in combination with the wood set;

Place the wood set exactly as described;

Make sure the ionization and spark electrodes and the surrounding space remain free

(see appendix 3, fig. 12 and 13);

In case of a wood set, keep the air openings between the burner and the vermiculite tray completely free;

Make sure there is no vermiculite's dust on the burner.

5.16.1 Placing the wood set

The wood set consists of a number of logs (see appendix 3, fig. 15), black vermiculite (see appendix 3, fig. 12) and

chips (see appendix 3, fig. 13) .

!Caution

The figures do not always show the correct colours.

Fill the burner with vermiculite and evenly spread the vermiculite (see appendix 3, fig. 16).

!Tip

You can influence the flame picture by moving the vermiculite.

!Caution

• The vermiculite should not get higher than the edge of the burner;

• The burner deck has to remain covered with vermiculite in order to prevent reduction of the burner's life

span.

Identify logs A to E (see appendix 3, fig. 15)

!Caution

Log E only applies to the Lugo 80.

!Tip

• Use the burn stains on the logs for identification;

• When placing the logs, use the positioning cams.

Place log A behind the burner against the positioning brackets (see appendix 3, fig. 17).

Place log B over the burner on the positioning bracket of the burner. Use the recess in the burner and keep the

ignitions free for the correct position of this log (see appendix 3, fig. 18).

Place log C against the positioning bracket and on log B (see appendix 3, fig. 19).

Place log D against the positioning bracket and on log B (see appendix 3, fig. 19).

In case of Lugo 80, place log E in the positioning bracket and on log B (see appendix 3, fig. 21).

!Caution

The logs should not block the burner cartridge and the ionization pens and ignition plugs should remain free,

because:

• The main burner will not ignite properly; which could result in unsafe situations;

• The appliance will become filthy more quickly, as a result of soot;

• The flame picture will be affected.

Fill the vermiculite tray with chips; spread the chips evenly (see appendix 3, fig. 20 (Lugo 70) and fig. 22 (Lugo 80)).

!Caution

Do not place chips on the open area around the burner and keep the ionization pens and ignition plugs free,

because:

• The main burner will not ignite properly; which could result in unsafe situations;

• The appliance will become filthy more quickly, as a result of soot;

• The flame picture will be affected.

If required, spread the glow material over the burner.

!Caution

The areas around the ionization and ignition should remain free from glow material.

!Tip

Fasten the glow material under chips and/or wood set.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU Lugo 80 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU Lugo 80

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info