Bedienungsanleitung EasyAlarm CONTROL (Seite 12 von 32) (Englisch)

515345

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

5.3 Sensor-3 monitoring

5.3.1 Sensor-3 as alarm contact

Note: if sensor-3 input is enabled as show below, you cannot disarm at any time!

Example: A normally closed contact shall trigger an un-delayed alarm with a hands-free-connection independent from

position of the selection switch.

1. Shift function switch to PROG

2. Enter sequence *. 9. 3. 1. 7 6 1 #. #..

 Current register (bit 7 -> bit 0) will be announced followed by “to modify press *., to stop press #.“

3. If you want to keep current value proceed with step 6. Otherwise start modifying register by pressing *.

4. Enter sequence 0. 0. 1. 0 0 0. 1. 1. .

R-Siren Entry-Delay Connect. mode Sensor on.. Type

0: off 0:off 0: Listening-in I / II / III 00: inactive

1: on 1:on 1: Hands-free 0 0 0 01: Normally open contact

0: enabled 10: Plug&Protect (auto-detected at power up)

1: disabled input-3 is open => Normally open monitoring

input-3 is closed => Normally closed monitoring

11: Normally closed contact

5. Press key #. .

 The new register (bit 7 -> bit 0) will be announced

6. Shift function switch to OFF

5.4 Acoustical monitoring

The acoustical monitoring is enabled if selection switch is on position III. In case the alarm conditions is fulfilled a

listening-in connection is established without any delay If you want to change this factory default you can proceed as

following:

Example: Acoustical monitoring enabled on II and III starting a hands-free connection without delay.

1. Shift function switch to PROG

2. Enter sequence *. 9. 3. 1. 7 5 9 #. #..

 Current register (bit 7 -> bit 0) will be announced followed by “to modify press *., to stop press #.“

3. If you want to keep current value proceed with step 6. Otherwise start modifying register by pressing *..

4. Enter sequence 0. 0. 1. 1 0 0. 0. 1. .

R-Siren Entry-Delay Connect. mode Sensor on.. Type

0: off 0:off 0: Listening-in I / II / III 00: Monitoring independent from arm/disarm state

1: on 1:on 1: Hands-free 1 0 0 01: Monitoring only in armed state

0: enabled

1: disabled

5. Press key #. .

 The new register (bit 7 -> bit 0) will be announced

6. Shift function switch to OFF

The sensitivity of the acoustical monitoring depends on selected position of the selection switch:

Position Alarm conditions (Function switch auf ON)

I Low sensitivity (LOW) => Alarm will be triggered if the noise level exceeds several times within a long

period (approx. 8 activations)

II Medium sensitivity (MED)

III Highest sensitivity (HIGH) => Alarm will be triggered if the noise level exceeds a few times within a short

period (approx. 3 activations)

Factory default for sensor

3 monitoring

00 0 111 00, => inactive on all positions I/II/III

Factory default for acoustical monitoring

00 0 110 01, => un-delayed alarm in listening-in

connection only on position III, inactive if disarmed

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EasyAlarm CONTROL Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von EasyAlarm CONTROL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info