Bedienungsanleitung EasyAlarm CONTROL (Seite 14 von 32) (Englisch)

515345

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

6.2 Designation of the calling number sequence

6.2.1 Standard sequence

Alarm triggered Calling number 1

Alarm not acknowledged

by called party 1

Calling number 2

alarm not acknowledged

by called party 2 same for calling number 3 to 9

The alarm is acknowledged by pressing DTMF 0 ( section 7.7.5).

The alarm is passed to next party immediately by pressing DTMF 8 or after connection time-out.

6.2.2 How to program calling number sequence

1. Slide function switch to PROG

2. Enter * * 0.

 Current calling number sequence will be announced followed by “to modify press * , to stop press # “

3. To maintain the current programming, go to point 5. Otherwise enter *. .

4. Enter the desired sequence (max. 9 digits)

5. Slide function switch to OFF

Sample for programming calling number sequence:

a) ’123’ => calling number 1 will be dialled, followed by calling number 2, followed by calling number 3.

b) ’111133322’ => first calling number1 will be dialled (4 call attempts are made), followed by calling number 3 (3 call

attempts are made), followed by calling number 2 (with 2 call attempts).

Notes:

 The calling number sequence is factory set to ‘123456789’, but a general reset according to section 10.1 will NOT

RESET the calling number sequence!

 In case of an un-programmed or deleted calling number, the calling number sequence will continue with the next

number of the sequence.

 If a dialled number is busy and another call attempt is programmed, the waiting period before re-dialling is 30 sec.

 If the calling number changes within the sequence, dialling of a new number starts without delay

6.3 How to select user language / How to record individual message

An individual announcement can be recorded as follows:

1. Shift function switch to PROG

2. Enter * * #.

 Current individual message will be announced followed by “to modify press * , to stop press # “

3. Select language for user announcements: (facultative)

Press key 1 to 4 according to desired user language (i.e. 1=DE/2=FR/3=GB/4=IT)

4. Press * and start speaking

5. Press # to finish recording, max. duration is 12 seconds

 New individual message will be announced

6. Shift function switch to OFF

Note:

 Repeat step 3 and 5 until you are satisfied with individual message.

6.3.1 Remote recording of individual message during handsfree connection

1. Enter DTMF * * # #

 Current individual message will be announced followed by “to modify press * , to stop press # “

2. Select language for user announcements: (facultative)

Press DTMF 1 to DTMF 4 according to desired user language (i.e. 1=DE/2=FR/3=GB/4=IT)

3. Start recording by sending DTMF * , start talking (max. 12 s) and finish by sending DTMF # .

 New individual message will be announced

4. Wait until the message “Abort” confirms the end of the programming

Note:

 Remote recording can be enabled / disabled according to section 10.8.1.

if called party 3 does not acknowledge the alarm, the calling

number sequence is repeated the number of programmed alarm

repetitions times (default value: two alarm repetitions,

programming see section 10.2)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EasyAlarm CONTROL Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von EasyAlarm CONTROL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info