Bedienungsanleitung Eden World Tour Pro Series (Seite 5 von 51) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

706110

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

HI FIDELITY FOR LOW FREQUENCY

| 9

8 | HI FIDELITY FOR LOW FREQUENCY

EDEN

| WTP SERIES |

FRONT PANEL FEATURES - 7

EDEN

| WTP SERIES |

BEFORE YOU PLUG IN - 6

BEFORE YOU PLUG IN

In Before you plug in or use your amplier please ensure you know how to correctly operate your unit. Incorrect operation or

installation may lead to undesirable results or unit failure which can be avoided by reading this guide.

Ventilation and Cooling

Important: All World Tour ampliers have been designed to operate in the most demanding of conditions, to ensure your product

performs to the best level every time always ensure ventilation holes and cooling fans are unobstructed so that they can provide the

required airow for the product. The cooling system design for World Tour Pro products means that fans on the product will only

operate when required.

Cabinet Impedance Selection

Important: To get the best from your amplier always ensure that you match it with cabinets that of the right impedance. World Tour

Pro ampliers are tted with revolutionary new illuminated speaker outputs (powered units only) which provide indication of which

impedance cabinets to plug into which socket this is explained in more detail in the back panel segment of this document. To get the

full power from your amplier you will need to operate it at a 4ohm load (8ohm Bridge Mono).

Operating with no load

All Eden World Tour Pro ampliers can safely be used with no load as preampliers for studio recording or as pre ampliers for tone

shaping before a power amplier.

If you are ever unsure about the operation or correct use of a product please contact the store where you bought your amplier, they will be more than

happy to provide advice and support.

PRODUCT FRONT PANEL FEATURES

(For WTP900, WTP600 and WTPre)

All World Tour Pro ampliers are designed with the same front panel features. To understand what each feature does and how to use it

please follow the guide below.

World Tour Pro ampliers are tted with both active and passive inputs and an input gain control. This allows you to nely tune the

input signal and get the most out of your amplier. If an instrument is plugged into both inputs both sockets behave as active inputs.

The Active inputs change the impedance and input level of the signal to compensate for modern high output bass instruments.

1. Active Input: Plug your active or high output instrument into the amplier here.

2. Mute: Use this button to mute the ampliers input (engages mute indicator LED).

3. Passive Input: Plug you non active or low output instrument in here.

4. Mute Indicator: This LED will illuminate when the input for the amplier is muted. If a signal is played while in mute mode the light will

blink to let the user know that they are trying to play while in mute mode.

5. Input Gain: Fine tune the amount of signal sent to the preamp using this control. Use in conjunction with the input gain clip indicator to

get the best performance from your amplier. When the Tube mode of the amplier is in operation the input gain controls the amount

of Tube Gain applied to the signal.

6. Input Clip Indicator: This LED will illuminate when the input signal begins to clip. If clipping occurs slowly turn the input gain control to

the left until the clip light stays off. If the amber light periodically illuminates during playing but does not change to red this indicates you are

using the maximum amount of input signal achievable into the front of the amplier.

AMBER: If the indicator illuminates amber this means you have clipped the input stage of the amplier briey but not for a

prolonged period of time. If the indicator operates only in the amber stage you are getting the maximum from the input stage of

the amplier without causing undesirable clipping to your sound.

RED: When the indicator illuminates red it will stay on for at least 1 second or if playing continues to clip the input stage. If the

indicator shows red this means that it is likely the clipping that is occurring will be detrimental to your tone and you should lower

the level using the input gain control so that the clip light only reaches the Amber level described above.

Compressor

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eden World Tour Pro Series Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info