Bedienungsanleitung Eden World Tour Pro Series (Seite 6 von 51) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

706110

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

10 | HI FIDELITY FOR LOW FREQUENCY

HI FIDELITY FOR LOW FREQUENCY

| 11

EDEN

| WTP SERIES |

FRONT PANEL FEATURES - 7

EDEN

| WTP SERIES |

FRONT PANEL FEATURES - 7

World Tour Pro ampliers have a studio quality, high speed, soft knee compressor which allows you to easily achieve the right level

and amount of compression required for your playing style. The compressor not only acts quickly but it also adjusts its compression

dependent on where in the register notes are played. This means that you can set the compressor to avoid being able to play through

it, avoiding undesirable sound spikes regardless of how hard you play during your music.

7. Compressor Amount: Control the amount of compression applied to the signal here, the higher the level the more compression applied.

8. Compressor Indicator: When the compressor circuit is engaged the indicator LED will illuminate green. If the indicator changes to Amber

this means that the compressor level is being reached and compression is taking place. If the indicator changes to RED this means you are

spending a prolonged period of playing inside the compressor.

9. Compressor Switch: Turn compressor circuit off and on using this switch

10. Ratio: Adjust the Ratio of the compressor here.

Tube Stage

The World Tour Pro uses 2 tubes in its design. The rst tube provides signal control as used in many of Eden’s Traditional Ampliers.

The second tube is used entirely to provide the ability to add additional warmth to your amplier sound and produce a more driven

and aggressive sound without losing the overall denition of your playing.

11. Tube Mix: Turning the control to the right increases the signal sent through the tube stage. This control should be used in conjunction

with the input gain control when the tube is switched on to adjust the amount of tube gain applied.

12. Tube Indicator: When the indicator is green this shows that the tube circuit has been switched on.

13. Tube off / on: Turn the preamplier tube off and on here.

Enhance

Eden has used its Enhance control for many years to provide an easy way to quickly get the best tone from its ampliers. The Enhance

circuit provides an easy use EQ sweep allowing you to simultaneously boost very low bass, upper middle and high frequencies, while

cutting the lower mid frequencies. This allows players to quickly nd their sound before adjusting the ner EQ details with the EQ

stage of the amplier.

14. Enhance control: Adjust the Enhance sweep position using this control.

15. Enhance Light: When illuminated green this light shows that the Enhance circuit is on.

16. Enhance Switch: Turn the Enhance circuit for the amplier off and on here.

Equalization

The World Tour Pro Semi-Parametric EQ provides the ability to truly detail your sound, to get the most from your instrument, or

to achieve a particular tone or playing environment. The Eden EQ is designed with both a simple Bass and Treble control and an

adjustable 3 stage Mid-Frequency control.

17. Bass Control: Increase or decrease the amount of bass applied here, set a 0 the bass response will be at.

18. 30-300Hz: Use this control to choose the frequency to be adjusted by the Low control.

19. Low Control: Adjust the amount of lower mid frequency applied using this control, set at 0 the response will be at. Use in conjunction

with the 30-300 Hz control to dene where in the lower mid frequency changes are made.

20. 200Hz-2KHz: Use this control to choose the frequency to be adjusted by the Mid control.

21. Mid Control: Adjust the amount of mid frequencies applied using this control, set at 0 the response will be at. Use in conjunction with

the 200hz-2Khz control to dene where in the mid frequency changes are made.

22. 1.2KHz-12KHz: Use this control to choose the frequency to be adjusted by the High control.

23. High Control: Adjust the amount of upper mid frequencies applied using this control, set at 0 the response will be at. Use in conjunction

with the 1.2Khz-12Khz control to dene where in the upper mid frequency changes are made.

24. Treble Control: Increase or decrease the amount of treble applied here, set at 0 the treble response will be at.

25. EQ Clip: This light will illuminate when the EQ stage of the amplier is clipped. When making some adjustments to the EQ you may nd

increasing certain frequencies cause the EQ stage to clip. Avoid this at all times by ensuring the EQ light does not illuminate.

Output Clip Lights

Depending on the amplifier, output clip lights may be present on the front panel. In the case of the WTP900 there are 2 lights one for

each amplifier inside the unit. On the WTP600 there is a single output clip light and on the WTPPRE preamplifier there are no output

clip lights. In order to get the maximum performance from your amplifier pay attention to the clip lights when using the Master Volume

control.

Clip indicator (Power Stage): On units with clip indicators these provide the opportunity to get the most from your amplifier without

overloading it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eden World Tour Pro Series Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info