Bedienungsanleitung EdgeCraft Chef-s Choice - EdgeSelect-Pro 125 (Seite 5 von 12) (Englisch)

663875

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

The Chef’sChoice

EdgeSelect-Pro

™

Diamond Hone

Knife Sharpener Model 125 is equipped

with manually activated diamond dressing pads that can be used if necessary to clean any

accumulated food or sharpening debris off the surface of the polishing/stropping disks. We

strongly urge you to clean your knives before sharpening them. You will ﬁnd you can go months

or even a year or more before you need to dress these Stage 3 disks. Only if you sense a distinct

decrease in polishing efﬁciency will there by any need to use this convenient feature described

further in a subsequent section.

Each sharpening stage is equipped with elastomeric guide springs positioned over the sharpen-

ing disks to provide a spring action that holds the face of your knife securely against precision

guide planes in the right and left slots of that stage during sharpening.

Unless you have special blades designed to be sharpened primarily on one side of the edge

(such as Japanese Kataba blades) you will want to sharpen equally in the right and left slots of

each stage you use. This will ensure that the facets on each side of the edge are of equal size

and that the edge will cut straight at all times.

When sharpening in any stage the knife should, on sequential strokes, be pulled alternately

through the left slot and the right slot of that stage. Generally only a few pairs of pulls in

the left and in the right slot will be adequate in each stage; if your knife is very dull or if you

have been using a sharpening steel to sharpen, you may need to make many more pairs of

pulls in a given stage (see subsequent sections for more detail). Always operate the sharpener

from the front side. Hold the blade horizontal and level, slide it down between the plastic spring

and the guide plane and pull it toward you at a uniform rate as it contacts the sharpening or

stropping disks. You will be able to feel and hear the contact as it is made. Always keep the blade

moving uniformly through each stage; do not stop your pull in mid stroke. Consistent pull speed

of about 4 seconds per stroke for an eight (8) inch blade is recommended. The time can be less

for shorter blades and more for longer blades.

Never operate the sharpener from the back side.

Use just enough downward pressure when sharpening to ensure uniform and consistent contact

of the blade with the abrasive disks on each stroke. Additional pressure is unnecessary and will

not speed the sharpening process. Avoid cutting into the plastic enclosure. Accidental cutting

into the enclosure will not functionally impact operations of the sharpener or damage the edge.

Figure 1 (below) identiﬁes each of the three stages as described further in the following sections.

Figure 1. Chef’sChoice

EdgeSelect-Pro

™

Diamond Hone

Knife Sharpener Model 125.

Figure 2. Typical kitchen knife.

Heel

Bolster

Handle

Edge

Tip

On/Off

Switch

Stage 1

Stage 2

Stage 3

Spring

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EdgeCraft Chef-s Choice - EdgeSelect-Pro 125 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info