Bedienungsanleitung EdgeCraft Chef-s Choice - EdgeSelect-Pro 125 (Seite 6 von 12) (Englisch)

663875

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

instructions

rEaD this BEForE You start to sharPEn

The Chef’sChoice

EdgeSelect-Pro

™

Diamond Hone

Knife Sharpener Model 125 is designed

to sharpen either Straight edge or Serrated edge blades.

1. Sharpen Serrated Edge Blades only in Stage 3. Do not sharpen serrated blades in

Stages 1 and 2, as that will tend to remove more metal than necessary from the serrations.

See Section titled Procedure for Sharpening Serrated Blades for more details.

2. Straight Edge Blades can be sharpened in all three stages, however, use of Stage 1 may

be necessary only if the knife is very dull or if you wish to create an edge with extra “bite”.

See following Section for more details.

ProcEDurE For sharPEninG straiGht EDGE BlaDEs

straiGht EDGE BlaDEs: sharPEninG First timE

Before you turn on the power, remove the cover positioned over Stage 1 and slip a knife blade

smoothly into the slot between the left angle guide of Stage 1 and the elastomeric spring.

Do not twist the knife. (See Figure 3.) (Retain the Stage 1 cover as a ready reminder of the

sharpening steps.)

Move the blade down in the slot until you feel it contact the diamond disk. Pull it towards you,

lifting the handle slightly as you approach the tip. This will give you a feel for the spring tension.

Remove the knife and press the Power Switch. A red “indicator” on the switch appears when this

switch is turned “ON.”

Stage 1: (If your knife is already reasonably sharp, skip Stage 1 and go directly to Stage 2.) If you

are sharpening a knife for the ﬁrst time, if the knife is very dull or if the knife has been sharpened

with a sharpening steel, start in Stage 1. Pull the knife once through the left slot of Stage 1 (Figure

3) by slipping the blade between the left angle guide and the polymeric spring while pulling the

blade toward you and simultaneously moving the blade downward in the slot until it engages

the diamond coated disk. You will hear it make contact with the disk. Insert the blade as close as

possible to its bolster or handle. If the blade is curved, lift the handle slightly as you sharpen near

the tip of the knife, keeping the blade edge approximately parallel to the table. Sharpen the entire

blade length. For an eight (8) inch blade, each pull should take about 4 seconds. Pull shorter blades

through in 2-3 seconds and longer blades in 6 seconds. Next, repeat with one full length pull in

the right slot of Stage 1.

Note: Each time you insert the blade you should simultaneously pull the blade toward you. Never

push the blade away from you. Apply just enough downward pressure to make contact with the

wheel - added pressure does not modify or speed the sharpening process.

Figure 3. Stage 1. Inserting blade in slot between guide

and elastomeric spring. Alternate left and right slots.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EdgeCraft Chef-s Choice - EdgeSelect-Pro 125 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info