Bedienungsanleitung Edilkamin Mito Idro (Seite 20 von 32) (Englisch)

810921

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

ENGLISH

IGNITION

With the b

oiler-stove

in stand-by mode, (after having

checked

that the chamber is clean), press the key

, and the

ignition procedure will start.

On the display

the wording

“ON AC” (start combustion)

will appear; after certain control cycles and after check-

ing that the pellets are burning, the display will show

the

wording

“ON AR” (heating on).

This phase will last a few minutes, to allow the ignition

procedure to complete correctly and for the exchangers

in the b

oiler-stove

to heat up.

After a few minutes, the b

oiler-stove

will enter the heating

phase, indicating

the wording

“burn” and later, during

regular functioning, the temperature of the output water,

set by the user, is indicated and the power chosen by the

automatic modulation system.

SWITCHING OFF

Pressing the key , when the b

oiler-stove

is on, will

start the switching off phase, which involves:

• Stopping the delivery of the pellets

• Burning any pellets left in the chamber, keeping the

fume fan on (usually for about 10’)

• Cooling the boiler’s body while the pump remains on

until the shut-off temperature is reached

• The indication “OF” on the display together with the

minutes remaining until shut-off

During the switching off phase, the b

oiler-stove

cannot

be turned on again; when the switching off phase is

completed the system automatically goes into stand-by

mode.

AUTOMATIC FUNCTIONING

The user must set the output water temperature, which

must be assessed according to the type and dimensions

of the system, and considering the atmospheric tempera-

ture linked to the season.

The b

oiler-stove

automatically modulates power accord-

ing to the difference between the set temperature (set on

the display) and the temperature measured by the water

sensor; on reaching the desired temperature, the burner

will function at minimum, going to power level 1.

The output water temperature can be increased by press-

ing the

key

or decreased by pressing the key .

The display alternatively shows the desired temperature

and the power which is automatically chosen by the elec-

tronic modulating system.

ECONOMY FUNCTION

Function suitable for boilers installed in small-scale sys-

tems, or whenever minimum power operation causes ex-

cessive heating.

This function, managed automatically, allows for switch-

ing the boiler off once the set delivery temperature is ex-

ceeded.

When the delivery temperature falls below the set value,

the boiler switches back on automatically. Request acti-

vation of this function, if required, from the Technical As-

sistance Centre during initial start-up.

When the ECONOMY function is activated, the display

will visualise ‘Econ’ after the other information.

REMOTE ACTIVATION FUNCTION

By means of a special connection wire (code 640560),

the b

oiler-stove

can be switched on/off by a remote con-

trol device such as a GSM telephonic activator, an envi-

ronment thermostat, a zone valve, or in any case a device

with clean contact with the following logic:

Contact open = b

oiler-stove

off

Contact closed = b

oiler-stove

Activation and deactivation takes place 10” after the

transfer of the last command.

If the remote activation of the door is connected, the b

oil-

er-stove

can be switched on and off in any case by the

control panel; the b

oiler-stove

will always act according

to the last command received, whether for switching on

or off.

PLEASE NOTE:

If the remote activation function is used, decouple the

remote connection cable, using a relay, if the distance

between the remote device and the boiler exceeds the

length of the cable code 640560 (1.5 m).

Consult the instruction sheet of the connection cable for

more detailed information.

ROOM VENTLATION

The boiler stove is equipped with a room ventilation sy-

stem; for setting the desired ventilation level, follow the

instructions indicated below.

Briefl y press the SET button to access the AIR menu;

use the

+/- buttons to select the following ventilation modes:

AUTO: ventilation adjusts automatically depending on

the boiler stove’s power output

OFF: the fan is always in use to have a minimum air flow

which prevents the fan from any overheating situation

FAN1: manual ventilation adjustment to 20%

FAN2: manual ventilation adjustment to 40%

FAN3: manual ventilation adjustment to 60%

FAN4: manual ventilation adjustment to 80%

FAN5: manual ventilation adjustment to 100%

After selecting the desired setting, if no button is pres-

sed for 5 seconds the system automatically exits the AIR

menu and saves the last setting visualised on the display.

INTRODUCTION ABOUT USE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Mito Idro Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Mito Idro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info