Bedienungsanleitung Edilkamin Story (Seite 39 von 209) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

810770

Zoom out

Zoom in

Vorherige Seite

1/209

Nächste Seite

- 39 -

ENGLISH

INSTRUCTIONS FOR USE

Automatic mode from synoptic panel/remote control

Press the MENU button twice to switch from manual to

automatic mode and adjust the temperature desired for the

room (on the panel or the + and – keys on the remote control

to set the temperature between 10 and 29 ...., and the stove will

regulate the operating power required to reach it.

If the set temperature is lower than the room temperature,

the stove works at Power 1.

Shutdown

For greater comfort, the stove and the air vents go off

at the same power at which it was operating.

With the stove in operation mode press the 0/1 key for 2

seconds (on the synoptic panel or remote control). The

shutdown procedure will begin and the countdown is

displayed. This varies according to the power at which it

is running when the shutdown phase begins.

The shutdown phase (which will extinguish the ﬂ ame

without leaving any unburnt material in the combustion

chamber and cool the stove), consists of:

• Pellet loading ceases.

• Ventilation is activated at the level at which the stove

was operating.

• Smoke expulsion motor enabled.

Never unplug the stove during the shutdown process.

Setting the clock

Press the MENU button for 2 seconds and use the + and –

keys to follow the instructions given on the display to

access the ‘Clock’ menu. This allows you to set the time on the

electronic control board.

Then press MENU and the following data appears in

sequence – this can be adjusted:

day, month, year, hour, minutes, day of the week.

When ‘Save?’ appears on the display you can check that

the settings have been entered correctly before conﬁ rming.

Press MENU to save the information (‘Save OK’ then

appears on the display).

Weekly timer

Press the MENU button for 2 seconds to access the time setting

function and press the + key to access the weekly timer fun-

ction – ‘Program ON/OFF’ will appear on the display.

A maximum of three timer programs can be set for each

day of the week.

As you conﬁ rm via the MENU button, one of the following

options will appear:

- ‘No Prog.’ (no program is set).

- ‘Daily program’ (a single program is set for every day)

- ‘Weekly program’ (a program is set for each day of the

week).

Move from one to the other using the + and – keys.

Use the MENU button to conﬁ rm the ‘Daily program’

option and access the selection of the number of programs

(ignition/shutdown) to be set per day. Use the ‘Daily program’

option to set the identical program/s for every day

of the week.

The following will be displayed if the + key is pressed:

- No Programs.

- 1st daily program (one ignition and one shutdown per

day), 2nd daily program (same as before), 3rd daily program

(same as before).

Use the MENU button to show them in reverse order.

If the 1st program is selected, the ignition time is shown.

The display shows: 1 Ignition Hour 10.30; use the +/–

keys to change the hour and press MENU to conﬁ rm.

The display shows: 1 Ignition Minutes 10.30; use the +/–

keys to change the minutes and press MENU to conﬁ rm.

In the same way, adjust the shutdown times. The program is

conﬁ rmed by pressing the MENU button when ‘Save OK’ ap-

pears on the display. When conﬁ rming the ‘Weekly program’

the day to which the program is to apply must be selected:

1 Mon; 2 Tues; 3 Wed; 4 Thurs; 5 Fri; 6 Sat; 7 Sun

Once you have chosen the day by scrolling through them

with the + and – keys, conﬁ rm by pressing MENU and

proceed with the settings of the programs in the same way

as for the ‘Daily program’, selecting whether or not to

enable a program for each day of the week and choosing

the number and times of interventions.

Should you make a mistake whilst setting the programs

you can exit without saving by pressing the 0/1 key.

Note on ﬂ ame variability

The ﬂ ame may vary depending on the type of pellets

used, in addition to normal variability of the solid fuel

ﬂ ame and regular cleaning of the combustion chamber

carried out automatically by the stove.

N.B. The automatic cleaning process performed by the

stove does not replace the need for the user to vacuum the

stove when cold, prior to ignition).

Pellet reserve warning

Stoves are equipped with an electronic pellet detection

system. The detection system is integrated into the electronic

control board, allowing the stove to monitor how many kilos

of pellets are left. This veriﬁ cation is implemented at any point

whilst the stove is in operation mode. For correct system ope-

ration, it is important that the following procedure is adhered

with during the ﬁ rst ignition (that must be implemented by the

DEALER). Before starting to use the pellet detection system,

you must load and consume a full sack of pellets. This allows

for a brief running-in of the loading system. Hence, load 15 kg

of pellets. Then press the ‘reserve’ button once, thereby storing

the data into the memory that 15 kg have been loaded.

From now on the display will show the remaining pellets

as they decrease in kg (15…14...13).

Each time pellets are reloaded you must enter the quantity.

E.g. when loading 15 kg, simply press the ‘pellet load’ button

to enter this into the memory. For other quantities, or in the

event of an error, you can specify the quantity using the pellet

reserve menu as follows:

Press the MENU button for 2 seconds to view the SETTINGS.

Press + or – consecutively to view RESERVE.

Pressing the + key increases the Kg to be loaded, pressing the -

key reduces the Kg, pressing the - key repeatedly sets the load

to 00Kg (R on the display), which makes it possible to cancel

the residual load.

Edilkamin Story Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info