Bedienungsanleitung Elite Drivo II (Seite 47 von 127) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

782459

Zoom out

Zoom in

Vorherige Seite

1/127

Nächste Seite

x and 142mm (5,6 in.) thru-axle spacing.

20_ASSEMBLING YOUR DRIVO II

- Loosen the bike’s rear brake and place the chain on

the smallest rear sprocket and the largest front chainring.

Remove the quick release from the rear wheel.

- Insert the quick release and the dropout adapter (Rif.C)

on the Drivo II sprocket cassette (Pic. 19).

- Place the bicycle chain onto the smallest sprocket of

Drivo II (Pic 20).

- Fully fit the bicycle’s rear dropouts onto Drivo II’s

cassette (Pic. 21), paying careful attention to the correct

internal or external position, based on the type of bicycle:

- External triangle adapter (Rif. C) for road and time trial

bikes (130mm triangle) (Pic.22).

- Internal triangle adapter (Rif. C) for mountain bikes

(135mm triangle) (Pic. 23).

NOTE: the knurled side of the triangle adapter (Rif. C) must

be facing the bicycle dropout.

Securely ﬁx the bicycle to Drivo II and ﬁrmly close the quick

release. The resulting pressure should keep the bicycle dropouts

locked to the Drivo II.

21_INSTALLING THE SPROCKET CASSETTE

ON THE Drivo II FOR Ø12 L=142 mm

CHAINSTAYS

- For bikes with rear thru-axle you need to change the

sleeve set in the chainstay spindle:

1) If it’s inserted, remove the left adapter (Ref. D) and

unscrew the right adapter for 130-135 mm chainstays

(Pic.24);

2) Screw the right adapter to its end (Ref. E) and insert the

left adapter (Ref. F) for 142 mm chainstays (Pic.25);

3) Attach the spacer (Ref. E) with the 17mm key (11/16

inches) with a 5Nm tightening torque (44 in-lbs). Use a

medium strength, oil-tolerant threadlocker to lock the nut

on the spindle;

4) Loosen the rear brake of the bicycle and place the chain

on the smallest sprocket of the rear wheel and the front

chainring. Remove the thru-axle from the rear wheel.

5) Position the bicycle’s rear dropouts on the axle of the

sprocket cassette of the Drivo II.

6) Insert the thru-axle on the Drivo II sprocket cassette

shaft.

7) Make sure the bicycle is safely positioned on the Drivo

II and lock the thru-axle with a strong push. The pressure

should make the bike dropouts remain locked onto the

structure of the Drivo II.

Make sure the bike is stable by pushing and pulling the

top tube of the frame and the saddle. Should the bike still

be moving a little on the Drivo II, use more force to lock

the thru-axle.

- Start pedalling. Ride very slowly at first and increase

your speed gradually until you become familiar with the

features of Drivo II.

22_CONNECTIONS

- Drivo II has an electronic motherboard that is powered via

a standard power supply adapter (included).

- Connect the power supply to the grid and the jack to

the proper connector on the back of the Drivo II. A small

vibration indicates that the system is booting up to its initial

position. This operation might last up to 15 seconds.

Hang the power supply cable on the dedicated hanger

(Pics 26 and 27).

- The Drivo II compliance with EU laws (see “Declaration

of conformity”, page 114) may be voided if a different

charger from the original is used.

23_REMOVING THE BICYCLE

- Shift the bicycle chain on the smallest cassette sprocket

of Drivo II and of the smallest front chainring of the bicycle.

- Open up the quick release (or remove the thru-axle) and

remove the bicycle from the Drivo II.

- To avoid clutter or for transportation: loosen the knobs (Pic.

28) and fold the side legs (Pic. 29 - 30).

24_RECOMMENDATIONS FOR USE

Choose a cassette range that is compatible with your goals

and fitness level:

1) cassettes with a range of 11 to 23/25 teeth are

recommended for professional athletes and amateurs who

are able to develop high power output.

2) Cassettes with a greater number of teeth, such as 12/

13 to 27 /29, are recommended for all other cyclists.

- Derailleurs should work properly after bicycle installation

on Drivo II. Occasionally, an adjustment may be necessary

for proper operation. If you have any questions, please

contact your dealer to ensure proper derailleur operation

with Drivo II.

25_INSTRUCTIONS ON HOW TO INSTALL

THE FREEHUB WITH CAMPAGNOLO®

9/10/11 SPEED SPROCKET CASSETTES

- To replace the original freehub body installed on Drivo

II with the accessory body compatible with Campagnolo®

9/10/11 speed cassettes, follow the procedure below:

1) Unscrew the adapter on the cogset shaft (Pic. 31).

2) Remove the freehub body from the Drivo II shaft (Pic.

32).

3) Fully insert the Campagnolo® cassette compatible

freehub body (Pic. 33-34).

4) Tighten the cog set shaft adapter using a 5 mm hex

wrench to a torque of 5 Nm (44in-lbs). Use a medium-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elite Drivo II Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info