Bedienungsanleitung Elite Drivo II (Seite 46 von 127) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

782459

Zoom out

Zoom in

Vorherige Seite

1/127

Nächste Seite

operation of the Drivo II due to such interference.

Do not expose the Drivo II to direct sunlight for long periods

when they are not in use.

15_PRODUCT MODIFICATIONS

Also in view of any technical update, ELITE reserves

the right to make changes to the products or their

speciﬁcations without being obliged to notify or inform the

Customer beforehand for:

a) changes that do not affect negatively the product

performance;

b) changes required to meet or improve the product

speciﬁcations;

c) changes necessary for the products to comply with the

applicable legal requirements.

ELITE also reserves the right to supply these products

with these improvements without being obliged to or

responsible for applying the same modiﬁcations to any

previously purchased products, reserving also the right to

change prices and model availability according to market

conditions, component availability and other corporate

considerations.

16_DISCLAIMER

Elite S.r.l. is not liable for any temporary or permanent

damage to the physical integrity of the user, whether direct

or indirect, resulting from the use of the trainer.

17_NAME AND LIST OF COMPONENTS

Your Drivo II electronic trainer is made of the

following components:

N°1 Drivo II body (Ref. A)

N°2 Freehub body spacer (Ref. B)

N°1 Chainstay adapter (Ref. C)

N°1Left chainstay adapter

L=130-135 mm (5,1-5.3 inches) (Ref. D)

N°1 Right chainstay spacer adapter

L=142 mm (5,6 inches) (Ref. E)

N°1 Left chainstay spacer adapter

L=142 mm (5,6 inches) (Ref. F)

N°1 Power supply (Ref. G)

N°1 Quick release (Ref. I)

N° 1 Left leg (Ref. L)

N° 1 Right leg (Ref. R)

N° 1 Central support (Ref. O)

N° 2 TBEI M6x60 screws (Ref. P)

N° 6 M6 washers (Ref. Q)

N° 2 M6 nuts (Ref. S)

N° 2 TBEI M8x35 screws (Ref. T)

18_ASSEMBLING THE DRIVO II

- Disassemble the Drivo II body (Ref. A)

- Place the Drivo II body (Rif. A) vertically as indicated

(Pic.1) and hold it in place with the upper handle

- Spread the leg until you can hear the safety lever click

(Pic.2 and Pic. 3).

- Place the home trainer on a flat surface and insert the

side legs (Ref. L and Ref. R) (Pic. 4).

- Screw the M8x60 screws with the washers and the M8

nut (Ref. P – Q – S ) until it touches the side legs and starts

rotating them (Pic. 5).

- Spread the side legs (Ref. L - Ref. R ) to its max extent

(Pic 6).

-The centering pin must be aligned with the bracket holes

(Fig. 7).

- Tighten the safety knob (Pic. 8).

- Insert the central support (Ref. O)(Pic. 9)

- Tighten the screws + M8 washers (Ref. T- Q)(Pic. 10)

- Make sure the hometrainer is stable (Pic 11), otherwise

operate on the adjustable feet (Pic 12A - 12B).

- Warning! the central support must remain at least 3 mm

above ground (Pic. 13).

19_INSTALLING THE SPROCKET CASSETTE

ON THE DRIVO II FOR M5 L=130 MM AND

L=135 MM CHAINSTAYS

- Assemble the sprocket cassette on the freehub by

aligning the groove profiles.

- 2 spacers (Ref. B) are usually needed for the Shimano®

/ SRAM® 9 speed cassette (Pic. 14), 1 spacer for the 10

speed cassette (Pic. 15) and no spacer is required for the

11 speed cassette (Pic. 16). Depending on the cassette

brand you are using there might be some differences with

the aforementioned general data.

- Using the torque wrench, tighten the lock ring supplied

with the cassettes onto the freehub body (Pic. 17).

CAUTION!

Strictly follow the instructions provided by the cassette

manufacturer with regard to specific installation

techniques, the need for additional spacers and torque

specifications.

NOTE: please contact your dealer if you have questions or

are unable to install the cassette. The warranty does not

cover any damage to the bicycle and/or Drivo II in the event

of incorrect installation.

- Drivo II includes the correct 5mm diameter quick release

adapter for dropout spacing ranging from 130mm (5,1

inches) to 135mm (5,3 inches). Therefore, on bikes with

130-135mm (5,1 to 5,3 inches) dropout spacing, insert

the left dropout adapter (Ref. D) (Pic. 18). Please consult

the paragraph 21 for bikes with 12mm diameter (0.47 in.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elite Drivo II Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info