Bedienungsanleitung Elite Drivo II (Seite 48 von 127) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

782459

Zoom out

Zoom in

Vorherige Seite

1/127

Nächste Seite

strength oil tolerant threadlocker to lock the adapter on

the shaft.

- 2 spacers (Ref. B) are usually needed for the 9 speed

cassette (Pic. 14), 1 spacer for the 10 speed cassette (Pic.

15) and no spacer is required for the 11 speed cassette

(Pic. 16). Depending on the cassette brand you are using

there might be some differences with the aforementioned

general data.

ATTENTION!

Strictly follow the instructions provided by the cassette

manufacturer with regard to specific installation

techniques, the need for additional spacers and torque

specifications.

NOTE: Please contact your dealer if you have questions

about installation or if you cannot install the cassette. The

warranty does not cover any damage to the bicycle and/or

Drivo II in the event of incorrect installation.

26_MAINTENANCE

Drivo II does not require any specific scheduled

maintenance, however the following precautions are

recommended:

- wipe the trainer clean with a cloth after each training

session to prevent the accumulation of dust and sweat;

- Do not clean or degrease the bicycle chain while the bike

is mounted on Drivo II as solvents can cause irreparable

damage to the bearings or other internal mechanical parts;

- Check that the quick release is properly secured and fully

working before every training session.

WARNING: The tension of the internal transmission belt is

tested on every product by Elite’s assembly department;

do not alter belt tension as the power sensor must be

recalibrated with every variation in belt tension.

- The belt tension may lessen after multiple uses or

after particularly intensive training sessions, and as a

consequence, the accuracy of the transmission of the

user power output may reduced. If that’s the case, you

might need to increase the transmission belt tension by

the following method:

1) Remove the motherboard cover (Pic. 35).

2) loosen the adjustment locking screw by one full turn, so

that you can then turn the adjusting nut (Pic. 36).

3) Turn the adjusting nut half a turn to tighten the belt

correctly (Pic. 37).

4) Begin the calibration procedure as indicated in

paragraph on page 41.

5) Repeat the previous operation if data transmission still

not correct.

6) Once calibration is done replace the motherboard cover

(Pic. 38).

WARNING!: Make sure the re-tensioning procedure has

been pre-approved by Elite’s tech assistance department

before re-tensioning the belt (Pic. 39). Breaking the anti-

tampering seal invalidates the product’s warranty.

27_WARNING

- Drivo II becomes hot during use. Wait for it to cool before

touching the resistance unit covers.

- Use the Drivo II trainer as described in the manual.

- Drivo II is not equipped with an emergency brake.

- Drivo II has been designed and manufactured to ensure

maximum safety of the user and/or third parties, but

people, children and pets should be kept away from the

trainer during use as contact with the moving parts of the

trainer and the bicycle may result in damage or injury.

- Never put your fingers or foreign objects of any kind

through the slots on Drivo II, as there will be high risk of

damage to the trainer and/or serious physical injury.

- Before you start training, place the trainer in a suitable

location, away from any potentially dangerous objects

(furniture, tables, chairs...) so as to avoid any risk of

accidental or inadvertent contact.

- The Drivo II is to be used by only single rider at a time.

- The max weight limit of the user is 113 kg / 250 lb in

accordance with the referenced norm EN 957-1 Class HC.

- Always check the safety and stability of the bicycle on

Drivo II before training.

- No part of the product has any use beyond its original

application. The warranty will be void if the unit has been

opened or tampered with.

- Since the feet are made of soft non-slip material, they

may leave traces of rubber on the floor during use.

- Do not leave the charger plugged in while not in use.

- Do not store the Drivo II in cold and damp places. This

may damage its electronic components.

- Use only the supplied charger. The Drivo II

compliance with EU laws (see “Declaration of conformity”,

page 114) may be voided if a charger different from the

original is used.

28_PACKAGING

If the roller needs to be shipped, careful packaging is

critical:

- remove the charger cable from the Drivo II;

- put the cable in a humidity-free container;

- pack up the Drivo II in its original box.

Concerning shipments, packages often undergo strong

shocks and bumps, so any non-original packaging might

irreparably damage the home trainer. Such damages are

not covered by the warranty.

Note: before shipping the home trainer or any of its

components to customer service, constult Elite or its

distributor or your own retailer.

Any non-planned shipment might not be accepted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elite Drivo II Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info