Bedienungsanleitung Elkron MP110 (Seite 12 von 20) (Englisch)

741484

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

(((ELKRON)))

MP110 USER MANUAL

(((ELKRON)))

MP110 USER MANUAL

1. Enter MASTER code

2. Press keys

EXIT

TEL

in sequence

3. The display will visualize the two flashing digits corresponding to the

first voice number; by keys

and

it is possible to go to other

numbers to be programmed.

4. Press key

corresponding to the telephone number to be

programmed. The digits will remain on in a fixed mode.

5. Press key

: approx. every 1 s. the digits of the first

telephone number are visualized (one digit at a time). For every

visualized digit, the buzzer will beep twice (in case of no programmed

digit, the display will visualize “- - “. Once completed the number

visualization, you go back to point 3).

6. Press key

to access the introduction of a new number (the display

will show “n” flashing”). By means of the numeric keys, enter the desired

number. To introduce a pause, enter C** followed by one numeric key

corresponding to the desired length of the pause (see side table).

7. Press key

to confirm and save the entered number. The

buzzer beeps twice to confirm operation and you go back to point 3.

8. To cancel a previously programmed telephone number proceed up to

point 4 and then press key

followed by key

. The

telephone number is cancelled.

9. Press key

EXIT

twice to exit from programming.

8.Telephone Number Programming

AVAILABLE PAUSES

, 1 = 1sec. ---->

, 5 = 5sec. ---->

, 9 = 9sec. ---->

9. Telephone Line Test

1. Enter MASTER code +

2. The keypad display will visualize symbol (on in fixed mode).

3. Press key

to start procedure.

The keypad display will visualize the following message:

(flashing).

4. At the end of the test, you go back to the main menu of the

communicator parameters.

5. Press key

EXIT

to exit.

6.Clock Setting

1- Enter MASTER code

2- Press in sequence

and

3- The display will show “Prog. Time hh:mm”

4- Enter a value between 00 and 23 ( 2 digits required)

5- Enter a value between 00 and 59 ( 2 digits required)

• To confirm and store the entered time, press key

• Before storing the entered time, the entered data are controlled. In case

of inconsistency, an error beep is generated and you go back to point

3. In case of correct data, the new time is stored and the positive result

of the operation is confirmed by an OK beep. When quitting by timeout,

the modification is not saved.

6.2 Date Modification

1- Enter MASTER code

2- Press in sequence

and

3- The display will show “PRG DATE dd-mm-yy”

4- By means of the numeric keys enter the date of the desired day (2 digits

from 0 to 31).

5- Enter a value from 01 to 12 (2 digits) corresponding to the desired month.

6- Enter a value from 00 to 99 (2 digits), corresponding to the desired year.

7- To confirm and store the entered date, press key

• The system carries out no control on the consistency of the entered

data; the operator shall therefore ascertain that the programmed day/

month data are correct before confirming. When quitting by timeout, the

modification is not saved.

6.1 Hours/Minutes Modification

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron MP110 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elkron MP110

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info