Bedienungsanleitung Elro AP5500 - Pro Alarm System (Seite 11 von 49) (Englisch)

708667

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

where you plan to install detectors. Check that the

Control Panel acknowledges the signal from the

Remote Control each time the ‘DISARM’ button is

pressed.

5. Press to return to the top level menu of

TEST MODE.

PASSIVE INFRARED DETECTORS

PIR detectors are designed to detect movement in a

protected area by detecting changes in infra-red

radiation levels caused, for example, when a person

moves within or across the devices field of vision. If

movement is detected an alarm signal will be emitted,

(if the system and alarm zone is armed).

Note: PIR detectors will also detect animals, so ensure

that pets are not permitted access to areas fitted with

Passive Infra-Red Detectors when the system is

armed.

Any number of PIR Detectors can be used with your

system, providing they are all coded with the system

house code and are mounted within effective radio

range of the Control Panel.

The PIR Detector uses a PP3 Alkaline battery which

under normal conditions will have typical life of up to 1

year. When the battery level drops, with the PIR in

normal mode and the battery cover fitted, the LED

behind the detection window will flash. When this

occurs the batteries should be replaced as soon as

possible.

CHOOSING A MOUNTING LOCATION

The recommended position for a PIR Detector is in the

PCB Position

Range

12m

Note: The range as indicated above refers to the

linear distance in front of the PIR sensor.

When considering and deciding upon the mounting

position for the detector the following points should be

considered to ensure trouble free operation:

1. Do not locate the detector facing a window or

where it is exposed to or facing direct sunlight.

PIR Detectors are not suitable for use in

conservatories.

2. Do not locate the detector where it is exposed to

ventilators.

3. Do not locate the detector directly above a heat

source, (e.g. fire, radiator, boiler, etc).

4. Where possible, mount the detector in the corner of

the room so that the logical path of an intruder

would cut across the fan detection pattern. PIR

detectors respond more effectively to movement

across the device than to movement directly

towards it.

corner of a room mounted at a height between 2 and

2.5m. At this height, the detector will have a

maximum range of up to 12m with a field of view of 110°.

The position of the PCB inside the PIR can be set to 5

different positions to adjust the range of the detector.

Setting the PCB in position 3 will reduce the range to

9m approximately, with position 1 providing a range of

6m approximately. The recommended position setting

for the PCB is in position 5.

Less Sensitive More Sensitive

5. Do not locate the detector in a position where it is

subject to excessive vibration.

6. Ensure that the position selected for the PIR

110¢X

TOP VIEW

detector is within effective range of the Control

Panel, (refer to ‘Testing the Control Panel &

Remote Control’).

12 10 8 6 4 2 0

UNIT:M

SIDE VIEW

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro AP5500 - Pro Alarm System Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro AP5500 - Pro Alarm System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info