Bedienungsanleitung Elro AP5500 - Pro Alarm System (Seite 13 von 49) (Englisch)

708667

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

where the detector may be affected by

environmental changes, (e.g. insects, air

temperature, etc). This feature is called

“sensitivity detection” and may be selected for high

or low detection.

The recommended setting is for high sensitivity

detection. However, in cases of extreme

environmental problems or if unexplainable false

alarms are experienced, it may be necessary to

select low sensitivity detection.

Set the required sensitivity detection using DIP 5 of

SW3 as follows:

ON high sensitivity detection

OFF low sensitivity detection

Note: The higher the sensitivity detection the less

movement will be necessary before the PIR

detector will trigger the alarm.

5. The setting of the DIP4 & DIP5 of SW3 can be

distinguished from the LED indication as follows:

Position

of DIP4

& 5 of

SW3

DIP4 of

SW3

DIP5 of

SW3

Trigger reaction of LED

Walk Test

mode

High

Sensitivity

LED will be on shortly.

It implies high

sensitivity.

Low

Sensitivity

LED will flash three

times and Illuminate

once. It implies low

sensitivity.

OFF

Normal

mode

Low

Sensitivity

LED does not light up

6. Connect the PP3 Alkaline battery to the battery clip.

Note: When the 9V Alkaline battery is connected,

the LED behind the lens will flash for 2-3 minutes

until the PIR has warmed-up and stabilized. The

LED will then stop flashing and turn OFF.

TESTING THE PIR DETECTORS

Ensure that the system is in Test Mode.

With the PIR detector set in Test mode and mounted in

position on the wall, allow 2-3 minutes for the detector

to stabilize before commencing the Walk Test.

1. Use the and buttons to scroll

through the menu until ‘WALK TEST’ is displayed.

Press to activate Walk Test.

‘ Walk Test Waiting…’ will be displayed.

2. Walk into and move slowly around the protected

area, each time the detector senses movement the

LED behind the lens will flash. In addition, the

Control Panel will beep to indicate that the alarm

signal has been received and the identity of the zone

that the detector is configured for will be displayed.

If necessary adjust the detection range by changing

the mounting position of the PCB within the PIR

housing.

Note: In normal operation, the LED behind the PIR

lens will not flash on movement detection, (unless

the battery is low).

If necessary re-adjust the detection pattern by

changing the mounting position of the PCB within the

PIR housing.

3. Remove the back cover of the PIR detector. The

Control Panel should beep and display ‘Accessory

Tamper’ to show that the detector’s tamper switch

has been activated.

4. Press to return to the top level menu of

TEST MODE.

5. Reconfigure the PIR Detector for normal mode by

setting DIP4 of SW3 to OFF and refit in position.

Note: When the detector is fully installed i.e. battery

cover is refitted; the unit will not detect movement for

approximately 45 seconds after each activation. (This

feature is present to conserve battery power and

maximize the battery life).

MAGNETIC CONTACT

DETECTOR(S)

The Magnetic Contact consists of two parts; a Detector

and a Magnet. They are designed to be fitted to

either doors or windows with the Magnet mounted on

the moving/opening part and the Detector mounted on

the fixed door or window frame.

The Magnetic Contact Detector is powered by two

CR2032 type Lithium cells which under normal

conditions will have typical life of up to 1 year. Under

normal battery conditions the LED on the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro AP5500 - Pro Alarm System Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro AP5500 - Pro Alarm System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info