Bedienungsanleitung Elro AP5500 - Pro Alarm System (Seite 14 von 49) (Englisch)

708667

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

Detector will not illuminate when the Detector is

triggered, (unless in test mode). However, under low

battery conditions this LED will be illuminated for

approx. 1 second when the detector is triggered.

When this occurs the batteries should be replaced as

soon as possible.

The Magnetic Contact Detector has the facility to

connect an additional wired Magnetic Contact. This

additional contact must be of a normally closed contact

type with the contacts being opened in order to

generate an alarm condition.

Any number of Magnetic Contact Detectors can be

used with the system, providing they are all coded with

the system house code and are mounted within

effective radio range of the Control Panel.

CHOOSING A MOUNTING LOCATION

The Magnetic Contact Detector is suitable for mounting

in dry interior locations only.

Decide which doors/windows are to be protected by

fitting Magnetic Contact Detectors, (usually the front

and back doors as a minimum will have Magnetic

Contact Detectors fitted). Additional detectors may

also be fitted where required to other vulnerable doors

or windows, (e.g. garage, patio/conservatory doors

etc).

Ensure that the position selected for the Magnetic

Contact detector is within effective range of the Control

Panel, (refer to ‘Testing the Control Panel & Remote

Control’).

Note: Take care when fixing the Detector to a metal

frame, or mounting within 1m of metalwork (i.e.

radiators, water pipes, etc) as this could affect the radio

range of the device. If required, it may be necessary

to space the magnet and detector away from the metal

surface using a plastic or wooden spacer to achieve the

necessary radio range.

INSTALLING THE MAGNETIC CONTACT

DETECTORS

Ensure that the system is in Test Mode.

1. Remove the battery cover by sliding and lifting it off.

(DO NOT use a screwdriver to lever the cover off)

2. Remove the battery holder by carefully tilting up the

end and pulling the connector off of the printed

circuit board.

3. Mount the Detector to the fixed part of the frame

along the opening edge opposite the hinges using

either the double sided adhesive tape or screws

provided.

If fixing the Detector with screws; fit the Keyhole

slot in the top of the Detector over the head of the

smaller pan-head screw. Secure the bottom of the

Detector using the 12mm countersunk head screw

fitted within the battery compartment. You will

need to drill out the centre of the fixing screw hole

using a 3mm drill. Do not over-tighten the fixing

screws as this may distort or damage the casing.

4. Fit the Magnet to the moving part of the

door/window opposite the Detector using the

adhesive tape or 15mm fixing screws. Ensure that

the parallel gap between the Magnet and Detector

is less than 10mm and that the arrow on the

Magnet is pointing towards and aligned with the

mark on the Detector.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro AP5500 - Pro Alarm System Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro AP5500 - Pro Alarm System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info