Bedienungsanleitung Elro AP5500 - Pro Alarm System (Seite 15 von 49) (Englisch)

708667

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

5. If an additional wired Magnetic Contact is required,

this should be wired to the terminal block provided

in the battery compartment. The wired contact

should be connected using two core (24AWG) wire

of maximum length 1.5m.

A cable entry cut-out is provided beside the

terminal block in the battery cover.

6. Slide the batteries supplied into the battery holder,

ensuring that the positive (+) side is uppermost on

each battery as it is installed.

7. Carefully refit the battery holder onto the Detector

ensuring that the spring connectors slide onto

either side of the circuit board.

8. Refit the battery cover.

SETTING THE MAGNETIC CONTACT

DETECTORS

1. Located in the battery compartment is a row of 11

DIP switches.

2. DIP switches 1-8 are used to set the House Code

for the Magnetic Contact Detector and must be set

to the same ON/OFF combination as the House

Code DIP switches in all other system devices.

3. Configure the alarm zone which the detector will

operate on with DIP switches 9-11 as follows:

DIP 9

DIP 10

DIP 11

Zone 1

OFF

Zone 2

OFF

Zone 3

OFF

Zone 4

OFF

Zone 5

OFF

Zone 6

OFF

Note: If the setting of DIP switches 9-11 does not

conform to any of the above mentioned six criteria,

the Control Panel will not receive a trigger signal

from the magnetic contact detector.

4. If additional external contacts are wired to the

Detector, remove the jumper link S2 on the PCB.

IMPORTANT: If external contacts are not

connected, then jumper link S2 must be fitted for

the detector to operate correctly.

TESTING THE MAGNETIC CONTACT

DETECTORS

Ensure that the system is in Test Mode

1. Use the and buttons to scroll

through the menu until ‘WALK TEST’ is displayed.

Press to activate Walk Test.

‘Walk Test Waiting…’ will be displayed.

2. Remove the battery cover by sliding off.

As the battery cover is removed the LED on the

Detector will illuminate for approx. 1 second to

indicate that the tamper switch has been activated.

In addition, the Control Panel will beep to indicate

that an alarm signal has been received and

‘Accessory Tamper’ will be displayed.

3. Open the door/window to detach the magnet from

the Detector. As the magnet is parted from the

detector the LED will illuminate for approx. 1

second to indicate that the Detector has been

triggered. In addition, the Control panel will beep

to indicate that an alarm signal has been received

and the identity of the zone that the detector is set

for will be displayed.

Note: In normal mode with the battery cover fitted,

the LED on the detector will not illuminate when the

detector is triggered, (unless the battery is low).

4. If connected, operate the wired Magnetic Contact.

As the contact is opened the LED on the Detector

should illuminate for 1 second to indicate that it has

been triggered and the Control Panel will

acknowledge the alarm signal.

5. Refit the battery cover on the Detector.

6. Press to return to the top level menu of

TEST MODE.

ECE

1 2 3 4 5 6 7 8 9 10 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro AP5500 - Pro Alarm System Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro AP5500 - Pro Alarm System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info