Bedienungsanleitung Elro AP5500 - Pro Alarm System (Seite 12 von 49) (Englisch)

708667

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

Note: When the system is armed, household pets

should not be allowed into an area protected by a

PIR detector as their movement would trigger the

PIR and generate an alarm.

Note: DO NOT fix the detector to metalwork or

locate the unit within 1m of metalwork (i.e. radiators,

water pipes, etc) as this could affect the radio range

of the device.

INSTALLING THE PIR DETECTORS

Ensure that the system is in Test Mode.

1. Undo and remove the fixing screw from the bottom

edge of the PIR. Carefully pull the bottom edge of

the detector away from the rear cover and then slide

down to release the top clips.

7. To refit the PIR detector to the rear cover, offer the

detector up to the rear cover and locate the clips in

the top edge into the rear cover. Push the lower

edge of the detector into place and refit the fixing

screw in the bottom edge of the PIR to secure in

position. Do not over-tighten the fixing screws as

this may damage the casing.

SETTING THE PIR DETECTORS

Located on the PCB of the PIR Detector are two blocks

of DIP switches (SW2 and SW3).

Rear Cover

Fixing

Screw

2. Carefully drill out the required mounting holes in the

rear cover using a 3mm drill according to whether

the unit is being mounted in a corner or against a

flat wall.

3. Using the rear cover as a template, mark the

positions of the fixing holes on the wall.

4. Fix the rear cover to the wall using the two 18mm

No.4 screws and 25mm wall plugs, (a 5mm hole

will be required for the wall plugs). Do not over-

tighten the fixing screws as this may distort or

damage the cover.

5. Configure the PIR detector as described below.

Remember that on initial installation that the device

needs to be tested and should therefore be set in

Walk Test Mode.

6. Check that the detector PCB is located and set in

the correct position to give the detection zone

pattern required.

To adjust the PCB position, simply slide it up or

down ensuring that the location legs are aligned

with the required position number marked on the

board.

1. DIP switches SW2 (numbered 1-8) are used to set

the House Code for the PIR Detector and must be

set to the same ON/OFF combination as the House

Code DIP switches in all other system devices.

2. Set the alarm zone which the detector will operate

on with DIP switches 1-3 of SW3 as follows:

DIP 1

DIP 2

DIP 3

Zone 1

OFF

Zone 2

OFF

Zone 3

OFF

Zone 4

OFF

Zone 5

OFF

Zone 6

OFF

3. DIP 4 of SW3 is used to configure the PIR Detector

for walk test mode, which allows the operation of

the detector to be checked during installation

without triggering a Full Alarm.

ON Walk Test mode

OFF Normal mode

Note: On initial installation the detector should be

set into Walk-Test mode ready for testing.

4. The PIR Detector incorporates an anti-false alarm

feature designed to compensate for situations

Mounting Hole

Positions

Dip Switches

PCB Position

Indicator

PCB Board

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro AP5500 - Pro Alarm System Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro AP5500 - Pro Alarm System

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info