Bedienungsanleitung Elro HA68S (Seite 13 von 34) (Englisch)

536725

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

-11--54-

PIR detectors are designed to detect movement in a protected area by detecting

changes in infra-red radiation levels caused when a person moves within or

across the devices field of vision. If movement is detected an alarm signal will

be emitted, (if the system is armed and the alarm zone active).

Note: PIR detectors will also detect animals, so ensure that pets are not

permitted access to areas fitted with Passive Infra-Red Detectors when the

system is armed.

The PIR Detector adopts a 1/2 AA size 3.6V Lithium battery which under normal

conditions will have typical life in excess of 4 years. When the battery level

drops, with the PIR in normal mode and the battery cover fitted, the LED behind

the detection window will flash upon detecting movement. When this occurs the

batteries should be replaced as soon as possible.

CHOOSING A MOUNTING LOCATION

The PIR Detector is suitable for mounting in dry interior locations only.

The recommended position for a PIR Detector is in the corner of a room

mounted at a height between 1.8 and 2m. At this height, the detector will have

a maximum range of up to 10m with a field of view of 110°, subject to the

position for the PCB being set in 5. The position of the PCB inside the PIR can be

set to 5 different positions to adjust the range of the detector. Setting the PCB in

position 3 will reduce the range to 7m approximately, with position 1 providing a

range of 5m approximately. The recommended position setting for the PCB is in

position 5.

PASSIVE INFRARED DETECTORS

STATUS

This sets the users that the Latch Key facility will operate with. If set to ‘Partial’

the Latch Key will only operate with those users enabled in section ‘9-2 Set

Partial User’.

Default setting: All OFF

Scroll through the menu until ‘9-1 Set Latch Key’ is displayed. The current

setting will also be displayed.

To change the setting press .

Scroll through the available options, (All on, All-off and Partial), until the

required setting is displayed.

Press to save and exit, or

Press to exit without saving.

PARTIAL USER SETUP

This allows controls over which users the Latch Key facility operates with when

set to ‘Partial’.

Default setting: OFF

Scroll through the menu until ‘9-2 Set Partial User’ is displayed and press .

Scroll through the menu until the required user number (1-5) to be configured is

displayed. The current status will also be displayed.

To change the setting press .

Press to enable the Latch-Key for the user, or

Press to disable the Latch-Key for the user.

After configuring all Users as required press to return to the top level Latch

Key Setup menu.

TELEPHONE NUMBERS

Scroll through the menu until ‘9-3 Set Latch Key TEL Number’ is displayed

and press .

Scroll through the menu until the required telephone number (1-2) is displayed.

The current setting will also be displayed.

To change the number press .

Enter the new telephone number (32 digits max).

Press to save and exit, or

Press to exit without saving.

TESTING THE CONTROL PANEL & REMOTE CONTROL

1. Press , , to put the system into Test mode.

‘ TEST MODE – WALK TEST’ will be displayed.

2. Press to activate Walk Test. ‘Walk Test Waiting…’ will be displayed.

3. Press the ‘ARM’ button on the Remote Control. As the key is pressed the

Control Panel will beep and the type of the device and button will be shown

on the display.

Press the other buttons on the Remote Control in turn, as each button is

pressed the Control Panel will beep and show the button being pressed on the

display.

4. Test the range of the Remote Control by pressing the ‘DISARM’ button on the

Remote Control from in and around the property and from all locations where

you plan to install detectors. Check that the Control Panel acknowledges the

signal from the Remote Control each time the ‘DISARM’ button is pressed.

5. Press to return to the top level menu of TEST MODE.

ENEN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro HA68S Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro HA68S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info