Bedienungsanleitung Elro HA68S (Seite 11 von 34) (Englisch)

536725

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

-9--56-

MOUNTING THE CONTROL PANEL

1. Undo the two captive fixing screws on top of the panel and open the cover.

The cover is hinged along the bottom edge.

2. Unclip and remove the two back-up batteries on either side of the panel.

3. Hold the Control Panel in position on the wall and mark the positions of the

four fixing holes. Remove the Panel and drill four 5mm holes and fit the

25mm Wall Plugs.

IMPORTANT: Do not drill the fixing holes with the Control Panel in position;

as the resulting dust and vibration may damage the Control Panel’s internal

components and invalidate the guarantee.

4. Fit two 18mm No.4 screws into the top holes until almost fully home and hang

the Control Panel over these screws using the two keyhole slots in the top

corners of the panel casing.

5. Route the cable from the Power Supply Unit up behind and on the right hand

side of the Control Panel and connect the plug to the DC power socket in the

panel. Ensuring that the cable is not trapped between the panel and the wall.

6. Fix the Panel to the wall using two 18mm No. 4 screws in the lower two fixing

holes in the panel and tighten the upper fixing screws until they just grip the

casing. Do not over tighten the fixing screws as this could damage or distort

the casing.

7. Ensure that the ‘Reset’ and the ‘Hard-Wired

Siren tamper detect’ jumper links are set in the OFF position.

8. Connect battery leads to both back-up batteries and refit batteries.

Battery 1 (left): Red lead to +ve battery terminal

Blue lead to –ve battery terminal

Battery 2 (right): Blue lead to +ve battery terminal

Black lead to –ve battery terminal

IMPORTANT: Take care when connecting battery leads to the batteries as

connecting incorrectly could damage the batteries or the Control Panel.

Note: The Power LED may flash to indicate that the unit is being operated

from the back-up batteries and that mains supply is not present.

9. If fitted, remove the plastic film covering the LCD display and on the display

window on the cover.

10. Close the lid of the Control Panel and tighten the captive fixing screws.

11. Plug in and switch ON the Power Supply Unit, (the Power LED should

illuminate).

ARM

The system can be set in ARM mode using either the Remote Control or the

Control Panel as follows:

Remote Control:

Press the ‘ARM’ button,

Control Panel:

Press the Arm button followed by the User Password and then the Enter button:

User Password

By pressing , the programmed exit delay will be overrided to 5 seconds.

PART-ARM 1

The system can be set in PARTIAL Arm 1 mode using either the Remote Control

or the Control Panel as follows:

Remote Control:

Press the ‘PARTIAL ARM’ button, .

Control Panel:

User Password

By pressing , the programmed exit delay will be overrided to 5 seconds.

PARTIAL ARM 2

The system can be set in Partial Arm 2 mode using either the Remote Control or

the Control Panel as follows:

Remote Control:

Press the ‘PARTIAL ARM’ button twice, , .

Control Panel:

User Password

By pressing , the programmed exit delay will be overrided to 5 seconds.

DISARM

The system can be Disarmed using either the Remote Control or the Control

Panel as follows:

ENEN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro HA68S Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro HA68S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info