Bedienungsanleitung Elro HA68S (Seite 18 von 34) (Englisch)

536725

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

-49--16-

MAGNETIC CONTACT DETECTOR(S)

The Magnetic contact consists of two parts; a Detector and a Magnet. They are

designed to be fitted to doors or windows with the Magnet mounted on the

opening part and the Detector mounted on the fixed frame. Opening the

protected door/window will remove the magnetic field, trigger the Detector and

generate an alarm condition, (if the system is armed and the alarm zone

active).

The Detector is powered by one 3.6V 1/2 AA size Lithium cells which under

normal conditions will have typical life in excess of 5 years. Under normal

battery conditions with battery cover fitted the LED on the Detector will not

illuminate when the Detector is triggered, (unless in test mode). However, under

low battery conditions this LED will be illuminated when the detector is

triggered. When this occurs the battery should be replaced as soon as possible.

1. Use the and buttons to scroll through the menu until ‘WALK TEST’

is displayed.

Press to activate Walk Test. ‘Walk Test Waiting…’ will be displayed.

2. Walk into and move slowly around the protected area, each time the detector

senses movement the LED behind the lens will flash. In addition, the Control

Panel will beep to indicate that the alarm signal has been received and the

identity of the zone that the detector is configured for will be displayed.

If necessary adjust the detection range by changing the mounting position of

the PCB within the PIR housing.

Note: In normal operation, the LED behind the PIR lens will not flash on

movement detection, (unless the battery is low).

If necessary re-adjust the detection pattern by changing the mounting

position of the PCB within the PIR housing.

3. Remove the back cover of the PIR detector. The Control Panel should beep

and display ‘PIR Detector Tamper’ to show that the detector’s tamper switch

has been activated.

4. Press to return to the top level menu of TEST MODE.

5. Reconfigure the PIR Detector for normal mode by setting DIP1 of SW2 to OFF

and refit in position.

Note: When the detector is fully installed i.e. battery cover is refitted; the

unit will not detect movement for approximately 2 minutes after each

activation. (This feature is present to conserve battery power and maximize

the battery life).

Default setting: ON

Scroll through the menu until ‘5-2 Entry Delay Beep’ is displayed.

The current setting will also be displayed.

To change the setting press .

Press to enable the Entry-delay beep, or

Press to disable the Entry-delay beep.

EXIT DELAY BEEP

This controls the warning beep which operates during the Exit Delay period

when Full Arm is initiated.

Default setting: ON

Scroll through the menu until ‘5-3 Exit Delay Beep’ is displayed. The current

setting will also be displayed.

To change the setting press .

Press to enable the Exit-delay beep, or

Press to disable the Exit-delay beep.

PARTIAL ARM 1 SETUP

PROGRAM MODE

Code:

6. PARTIAL ARM 1

6-1Exit Delay

xx xxx SEC

Select

ON->* OFF->#

Input

(1-250) Secs

Select

ON->* OFF->#

6-2 Entry Delay

Beep: xxx

6-3 Exit Delay

Beep: xxx

Scroll through the programming menu until ‘6. PARTIAL ARM 1’ is displayed

and press .

Note: After configuring Partial Arm 1 press to return to the top level

programming menu.

ENEN

Select

ON-> OFF->#

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro HA68S Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro HA68S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info