Bedienungsanleitung Elro HA68S (Seite 26 von 34) (Englisch)

536725

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

-41--24-

With the system in Disarm Mode.

Press , ,

Admin Password

The system is now in the Programming Mode

Use the and buttons to scroll through the programming menu.

Press to select the displayed programming function or sub-menu.

Note:

After programming all required functions press to leave Programming mode

and return to Disarm mode.

RESET FACTORY DEFAULT

1. Press

, to place the system in Test Mode.

User Password

2. Undo the Control Panel cover fixing screws and open the cover.

3. Switch OFF the mains supply to the plug-in PSU Adaptor and remove the plug

from the DC power socket in the Control Panel.

4. Remove either back-up battery and disconnect the battery leads.

5. Set jumper link P1 to the ON position.

6. Reconnect the battery leads and replace the back-up battery in position.

Reconnect the PSU Adaptor plug to the DC power socket in the Control Panel

and switch On the supply to the PSU Adaptor.

7. As the Control Panel powers-up, ‘EEPROM RESET’ will be displayed while the

factory default conditions are restored to memory. Once the memory reset

has been completed ‘DISARM READY’ will be displayed. The Control Panel

will now be reconfigured with all factory default settings.

8. Reset jumper link P1 into the OFF position.

9. Close the Control Panel cover and refit the fixing screws.

PROGRAMMING INSTRUCTIONS

Note: After recording the message, press to stop the recorder and cancel

any remaining message time.

REPLAY ALARM MESSAGES

Scroll through the menu until ‘:3 Play Voice’ is displayed and press .

Scroll through the available menu options until the required message type is

displayed.

a) Main + Intruder Messages

b)Main + Fire Messages

c) Main + Panic Messages

d)Main + Medical Help Messages

To replay the message press .

Press to return to the top level Voice Dialer setup menu.

CALL ROUTING

This feature controls which telephone numbers are enabled in the dialing

sequence and are dialed when the voice dialer is activated.

The current routing sequence is displayed on screen in the order of phone

numbers 1-6. An ‘X’ indicates the number is disabled and a ‘O’ indicates the

number is enabled in the routing sequence. e.g. A display = “00000x” indicates

a call sequence of phone nos.1,2, 3, 4 and 5, phone number 6 is disabled and

not called.

Default setting: all numbers disabled.

Scroll through the menu until ‘:4 Alarm Dial’ is displayed. The current settings

will also be displayed.

Scroll through the available menu options until the required telephone number

(1-6) to be configured is displayed. The current status will also be displayed.

To change the setting press .

Press to enable the number in the routing sequence, or

Press to disable the number in the routing sequence.

TEL CONFIRM TIMES

This sets the number of acknowledged phone numbers required to stop the

voice dialer. For example if set to “2” then the dialing sequence will continue

until an acknowledgment is received from two different numbers, (e.g. Phone

No. 1 and Phone No. 3). The recipient must acknowledge the message by

pressing the button on their telephone keypad.

ENEN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elro HA68S Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elro HA68S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info