Bedienungsanleitung Enduro AS101 (Seite 43 von 48) (Deutsch, Englisch, Holländisch, Französisch)

722072

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

ENDURO

autoSteady 36

Ref: AS101-UM-TKI-0114-Rev. A

After pressing the reset button on the control unit, if have not any operation in more than 15 seconds, the re-

synchronization process will stop.

OPERATION - ELECTRONIC CONTROL UNIT

The electronic control unit (6), which is mounted inside your caravan, is responsible for controlling the

autoSteady system.

The control unit has three LED’s, one pushbutton and one slide switch (Fig. 13):

Green LED (Fig. 13A): Power LED continuously lights up when the system is activated (by moving slide switch

of the remote control to “On”-I). If the remote control is far away from the control unit, beyond the availably

distance, this LED will start blinking.

Blue LED (Fig. 13B): Error message LED concerning caravan battery:

• Blue LED is blinking (2 times blinking, break, 2 times blinking, break etc.): Battery voltage too low (<10V).

Battery needs to be recharged.

• Blue LED is blinking (4 times blinking, break, 4 times blinking, break etc.): Battery Voltage too high (over

charged). Try to discharge the battery by turning on a user (for example a lamp or water-pump).

Red LED (Fig. 13C) is blinking (6 times blinking, break, 6 times blinking, break etc.): Amp overload protection

is activated. Maybe the system has a current-shortage. Please check the whole system carefully. Wait about 60

seconds and try again.

In general all error messages will reset automatically after one minute. If this is not the case, reset the

electronics by switching off the system via the isolation switch and the remote control for at least 15 seconds

and then turning it on again.

The Reset Button (Fig. 13D): The remote control handset and the control unit are synchronised with each

other in the factory. If the control unit or the remote control handset is replaced, they must be re-synchronised

as described in chapter OPERATION - REMOTE CONTROL HANDSET: “How to synchronise the remote

handset with a new manoeuvring system or autoSteady control unit”

Jack-up force switch (Fig. 13E): The system is suitable for a big range of the caravans. To make sure that

the system is always working properly and your caravan is stable, the Current-protection can be adjusted via a

slide switch on the control unit (Fig. 13E):

L: Low current for caravans up to 1000kg

M: Normal current for caravans in the range of about 1000 – 1500kg

H: High current for caravans in the range of about 1500 – 2000kg

Different caravan chassis or floors have different situation for jack-up force. The above mentioned values are

just a rough indication. Please check what is the most convenient for your caravan so your caravan or caravan

chassis will not be damaged but still your caravan is stable.

OPERATION - GETTING STARTED

Please make sure you read the safety instructions very carefully and make sure that you

follow these guidelines!

Make sure that the battery that supplies the system is fully charged and in good condition.

Make sure that the caravan is free from the vehicle and the handbrake is on.

Before you can start using the autoSteady system, please make sure you caravan is already levelled out in all

directions. Please use the supplied tool (3) and accomplish this the usual way.

Just as the standard corner steady of your caravan can only be used for stabilising, also the

autoSteady system cannot be used for jacking up or levelling out your caravan.

Once the caravan is levelled out, you can start using the autoSteady system.

Turn on the battery power isolation switch (24).

Activate the autoSteady system by moving the slide switch to “On”-I on the remote control (Fig. 10A). The

green LED (Fig. 10H) will illuminate continuously. The system is ready for use.

During the operation of the system, the handbrake must be secured.

First check if the slide switch (Fig. 10O) is in “autoSteady” mode (Fig. 10Q).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Enduro AS101 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info