Bedienungsanleitung Eufab 11411 - Bike Two (Seite 9 von 20) (Deutsch, Englisch, Französisch, Italienisch)

807232

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Seal the ends of the tubes of the rack table using the rectangular plugs

60 x 30 [mm].

Inserting the plugs



Now mount the U-shaped bracket. To do this, insert four lock screws M6 x 70

from the inside, through the frame of the rack table and, from the outside,

place the U-shaped bracket onto the screws. Secure the U-shaped bracket

using washers and knurled nuts.

5.1.2 MOUNTING THE USHAPED BRACKET

To mount the rear lights,  rst place these in the protective moulds. Make

sure that the cable is  tted cleanly into the duct and is not crushed. The

rear lights with the reverse light is mounted on the right (in the direction of

travel) and the fog light is mounted on the left, in doing so, the openings for

license plate illumination for both lights must be on the inside. Now insert

the threaded bolts of the rear lights through the drilled holes in the rack

table and screw into place using washer and M5 nuts.

Mount the license plate holder using the already mounted screws and

washers to the rack traverse in such a way that the lamps and the license

plate holder are level. The mounting clips for securing the license plate are

push-out parts in the holder. Break out two of the clips. Slide the license

plate into the holder, then push the clips into the cut-outs to secure the

license plate.

5.1.6 MOUNTING THE WHEEL STOPPERS

Now push a wheel stopper on from above onto each of the wheel rails. Make

sure that the higher side of the wedge shape points towards the middle

of the rack. Insert a small tensioning strap through the middle opening of

each of the stoppers and under the wheel rail on the opposite side, then

back through the middle opening.



Tensioning strap 6 x

Stopper 4 x

5.1.7 MOUNTING THE FRAME HOLDER

Undo the handle screw of the frame holder and rotate out fully. Open the

cu of the frame holder and place the inserts around the U-shaped bracket

at a position suitable for your bicycle. Place the cu around the inserts and

push  rmly together. Close the frame holder using the handle screw (but

do not tighten).

Tighten the M16 screw slightly and align the bicycle rack parallel to the rear

of the vehicle. Now tighten the M16 screw in such a way to ensure that the

rack is securely attached and can no longer be rotated.

Regularly check the  rm seating of the rack on the trailer tow bar as well as

the functionality of the lighting systems.

5.2 MOUNTING THE BICYCLE RACK ON THE TRAILER TOW BAR

Make sure that the trailer tow bar is undamaged, clean and grease-free.

The bicycle rack is placed horizontally on the tow bar from above.

Slight signs of pressure on the tow bar ball are

normal and do not in uence the functionality.

M16 x 1.5 x 90 screw approximately one centimetre into the rack base.

Align all of the mounted parts and tighten all screw connections evenly and

 rmly.

Knob nut M6

Lock screw M6 x 70



Washer 6 mm

U-shaped

bracket

Protective mould left Washer 5 mm

5.1.3 MOUNTING THE REAR LIGHTS

Rear light, left

Protective mould rightNut M5

Rear light, right

Reversing light

Cut-out for installation clips

5.1.5 MOUNTING THE LICENSE PLATE HOLDER/INSERTING THE

LICENSE PLATE

Cut-out for installation clips

5.1.4 LAYING THE ELECTRICAL CABLES

Lay the cables alongside the pipe of the rack table. The cables may not be

kinked, stretched nor squashed. Secure the cables with the supplied cable

ties. When you are  nished, trim any excess material from the cable ties

using cutting pliers.

Clips

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eufab 11411 - Bike Two Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info