Bedienungsanleitung Faber Cas 1000 (Seite 13 von 50) (Deutsch, Englisch, Holländisch, Französisch)

706323

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

General Information

Only use ltered water in this appliance.

Unpack the appliance carefully and retain the packaging for possible future use, in the event of moving or returning the

re to your supplier.

Always ensure that the appliance is sitting on a level surface.

The appliance is a ame effect only.

The appliance is designed to be built into a surround or built into a wall.

Before connecting the appliance, check that the supply voltage is the same as that stated on the appliance.

Please note: Used in an environment where background noise is very low, it may be possible to hear a sound which is

related to the operation of the ame effect. This is normal and should not be a cause for concern.

Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.

The water tank, sump, sump lid, tank cap and air lters must be cleaned once every 2 weeks, particularly in hard water

areas.

If you intend not using the appliance for longer than 2 weeks, drain the water from sump and water tank and dry the

sump.

The sump and the water tank in this product are treated with a biocidal product, Silver Biocide. This conforms with the

latest relevant ISO standard

Do not drink the water from the sump or from the water tank(s)

This appliance is intended to be permanently connected to the water mains and not connected by a hose-set

Installation Instructions

This section describes how to set up your re.

BEFORE YOU START

1. Ensure that all packing items are removed (read any warning labels carefully) and retain all packing for possible

future use.

2. Before connecting the appliance, check that the supply voltage is the same as that stated on the appliance.

3. Ensure that the appliance is sitting on a level surface

4. Lift off the metal top plate to gain access to the appliance. Keep the top plate with the packing for possible future

use. (Fig.2)

Installation Guide

This product can be built into a wall, surround or structure. Please take note of the product dimensions in Fig.1 and

build your wall, surround or structure accordingly. You are required to leave a minimum of 400mm from the base of the

fuelbed to any shelf/enclosure above the product. This will allow enough space above the product to allow the ames to

form fully and not to be obstructed.

This product needs free ventilation from underneath to operate correctly. The free ventilation helps keep the electronic

components cool, allow the mist to evacuate the sump and lift out of the product effortlessly.

THE AREA OF FREE VENTILATION THE CAS500 REQUIRES IS A MINIMUM OF 210CM

THE AREA OF FREE VENTILATION THE CAS1000 REQUIRES IS A MINIMUM OF 420CM

Surround Design

The CAS500 and CAS1000 are designed to be built into a surround/wall. Using the dimensions provided in Fig1. you

can design a cavity for the appliance. Be sure to allow room under and around the appliance for the water connection

and the electrical connection. Once the surround/wall is prepared you can put the appliance in place. Fit the appliance

so you ensure that it is centered. When you have settled on a position, lift off the Fuelbed and using appropriate screws

for the surround/wall, screw through the formed holes in the left and right side panels securing the appliance in place.

Water Supply

The appliance can operate by using the water tank(s) provided or by connecting up mains water.

Water Tank(s): You will need to remove the ‘Fill Cap’ from the sump. (Fig.3a and Fig.3b). Place the Water Tank(s)

(Fig.3C) in your sink and remove the cap (turn anti-clockwise). Fill the Water Tank with ltered tap water only. This is

necessary to prolong the life of the ame and smoke producing unit. The water should be ltered through a conventional

domestic water lter unit and the lter should be replaced regularly. Distilled water must not be used.

Mains Water: If you choose to supply mains water to the appliance store the bottle(s) with the metal top plate and

packaging. You can use the Piercing Valve (supplied) to connect into your mains water supply by;

1. Clamp the Piercing Valve onto you water pipe: maximum 1/2” (12.7mm) pipe

2. Connect a 1/4” (6.35mm) PVC tube (not supplied) from the piercing valve into the water lter supplied and then in

to the product (Fig.4).

3. Turn the tap on the valve clockwise to pierce into the water pipe. Turn the tap anti-clockwise to allow the water to

ow through the valve. You can shut off the water to the product by turning the tap on the valve clockwise until the

ow stops.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber Cas 1000 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info