706323

Faber Cas 1000 Seite 15

15
Zoom out
Zoom in
Vorherige Seite
1/50
Nächste Seite
• is the test mode button. This will be used by the manufacturer and the Service Engineer
• is the reduce ame button. Press this to reduce the height/intensity of your ame. You will hear an audible beep
when you reach the minimum level
• is the increase ame button. Press this to increase the height/intensity of your ame. You will hear an audible
beep when you reach the maximum level
• is the reduce re crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off
• is the increase re crackling sound. Press this to increase the volume of the crackling sound.
Button panel ‘B’:- Controls the functioning of the left side of appliance
• is the test mode button. This will be used by the manufacturer and the Service Engineer
• is the reduce ame button. Press this to reduce the height/intensity of your ame. You will hear an audible beep
when you reach the minimum level
• is the increase ame button. Press this to increase the height/intensity of your ame. You will hear an audible
beep when you reach the maximum level
• is the reduce re crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off
• is the increase re crackling sound. Press this to increase the volume of the crackling sound.
GETTING THE DESIRED FLAME EFFECT
1. Switch the appliance on by pressing the main switch to the on position and pressing the on/standby button. The
ames will start after 45seconds. The ames will be at max height for 5seconds and then reduce to a nominal level
2. Press the and buttons to adjust the ame to your desired level. Please give the ame generator time to react
to the changes you make.
3. Do not tilt or move the appliance while there is water in the tank or sump
4. Make sure that the appliance is on a level surface
Once you have made you adjustments to both the ame height and crackling sound the appliance will keep these
settings even if you power off the appliance by either the on/standby button or by the main switch. The next time you
switch on the appliance it will start up as normal, wait 45 seconds for the ames to start, run at maximum height for 5
seconds and then revert to the adjusted settings.
RECEIVER CONTROLS
There are manual controls on the Receiver
CAS500
• is the on/standby button. Press it to turn on and off the ame effect.
• is the re crackling sound. Press this to turn on and off the crackling sound. The volume is adjusted on the
manual controls of the appliance
• is the reduce ame button. Press this to reduce the height/intensity of your ame. You will hear an audible beep
when you reach the minimum level
• is the increase ame button. Press this to increase the height/intensity of your ame. You will hear an audible
beep when you reach the maximum level
CAS1000
• is the on/standby button. Press it to turn on and off the ame effect.
• is the re crackling sound. Press this to turn on and off the crackling sound. The volume is adjusted on the
manual controls of the appliance
• is the reduce ame button for the left had side of the appliance. Press this to reduce the height/intensity of your
ame. You will hear an audible beep when you reach the minimum level
• is the increase ame button for the left had side of the appliance. Press this to increase the height/intensity of
your ame. You will hear an audible beep when you reach the maximum level
• is the reduce ame button for the right had side of the appliance. Press this to reduce the height/intensity of your
ame. You will hear an audible beep when you reach the minimum level
• is the increase ame button for the right had side of the appliance. Press this to increase the height/intensity of
your ame. You will hear an audible beep when you reach the maximum level
REMOTE CONTROL
The remote control is supplied with 2xAAA batteries. Remove the battery cover from the underside of the remote control
and after removing the batteries from the plastic wrapping t them into place. Replace the battery cover.
The remote control has wireless technology and is required to be paired to the receiver. This is done by pressing the
button on Button Panel ‘A’, the LED’s will start to blink on and off. This is to let you know that the appliance is ready to
connect to the remote control. Press the button on the remote control. The appliance will switch off. Now the remote
control is paired to the appliance.
… 15 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Faber Cas 1000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info