Bedienungsanleitung Faber Cas 1000 (Seite 14 von 50) (Deutsch, Englisch, Holländisch, Französisch)

706323

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

Operating the Product

4. Turn on the internal ball valve. This is located under the sump. Remove the sump as described under ‘Cleaning’ in

the Maintenance section

Please note: the water pressure is to be between 8Bar (800Kilopascals) and 0.5Bar (50Kilopascals).

If you do not feel condent making this connection please consult a qualied plumber, to ensure a safe and

secure installation.

Electrical Connection

Plug the re into a 13amp/240 volt outlet. Be sure to have access to the plug after installation to allow for disconnection.

Ensure that the supply cable exits at the back of the re, at the right or left hand corner to suit your supply socket location

and is not trapped under the re such that it might cause it to be damaged. If connecting multiple appliances into the

same outlet be sure not to connect more that 5 appliances. If more appliances are required they must be connected into

a separate circuit.

The appliance can be connected to the xed wiring of the premises through a suitable connection box positioned

adjacent to the appliance. This electrical installation must be carried out by a competent electrician and be in strict

accordance with the current I.E.E regulations for Electrical Equipment in Buildings.

The electrical can remove the supplied plug by the following;

1. Lift off the fuelbed and put switch ‘A’ into the off position (Fig 9).

2. Ensure that the appliance is unplugged.

3. Lift off the access cover by removing the retaining screw (Fig 15).

4. Unscrew and remove the Live, Neutral and Earth wires.

5. Unscrew the cable clamp (Fig 16 ‘A’) and remove the supply cord.

The electrician can then connect their wire from the appliance (by following the steps above in reverse) to the connection

box ensuring that it incorporates a double pole isolating switch having a contact separation of at least 3mm. Brown - Live

(L), Blue - Neutral (N) and Green/Yellow - Earth (E).

Connecting the Receiver

Take your Receiver, 4button for CAS500 and 6button for CAS1000, and with the Fuelbed removed insert the 3.5mm

jack into the socket at the back of the appliance (Fig.5). The Receiver has a cable length of 1.4m which will allow you

position it anywhere around the product. If you prefer to hide it the Receiver can be placed inside the surround/wall.

Please ensure that the Receiver is not enclosed in metal, concrete or any other dense material, this will affect the signal

from the remote control.

This section describes how to activate your re using either the manual controls or remote control.

MANUAL CONTROLS

The manual controls are located beneath the Fuelbed. (Fig.6)

CAS500

Mains Switch ‘A’:- Controls the electricity supply to the appliance.

Note: This switch must be in the ‘ON’ ( I ) position for the appliance to operate

Button panel ‘A’:- Controls the functioning of the appliance

• is the on/standby button. Press it to turn on and off the ame effect. Turning it on will be indicated by the main

lights activating. Although the main lights operate immediately it will take a further 45 seconds before the ame effect

starts.

• is the Pairing button. This will pair your remote control to the receiver. See ‘Remote Control Operation’ for details

• is the test mode button. This will be used by the manufacturer and the Service Engineer

• is the reduce ame button. Press this to reduce the height/intensity of your ame. You will hear an audible beep

when you reach the minimum level

• is the increase ame button. Press this to increase the height/intensity of your ame. You will hear an audible

beep when you reach the maximum level

• is the reduce re crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume

for this is off

• is the increase re crackling sound. Press this to increase the volume of the crackling sound.

CAS1000

Mains Switch ‘A’:- Controls the electricity supply to the appliance.

Note: This switch must be in the ‘ON’ ( I ) position for the appliance to operate

Button panel ‘A’:- Controls the functioning of the left side of appliance

• is the on/standby button. Press it to turn on and off the ame effect. Turning it on will be indicated by the light

activating. Although the main lights operate immediately it will take a further 45 seconds before the ame effect

starts.

• is the Pairing button. This will pair your remote control to the receiver. See ‘Remote Control Operation’ for details

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber Cas 1000 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info