Bedienungsanleitung Faber Vejen (Seite 8 von 20) (Englisch)

696805

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Installation manual

1 Dear user

Congratulations on purchasing your Faber product, a quality

product that will provide you with the warmth and atmosphere for

many years. Please read the user manual before using the re.

Should a malfunction occur despite the careful nal checks, then

you can always contact your Faber dealer.

In order to claim the guarantee, it is important that you register the

re. For this we have created a special site. You will nd all

information regarding the warranty during registration.

> Please note:

The data of your re is available in the user manual.

1.1 Introduction

Installation and maintenance of the re must be carried out by a

professional expert who has proven knowledge and demonstrable

competence. A professional craftsman takes into account all

technical aspects such as heat delivery, gas connection as well as

ue gas discharge requirements.

Where the installation instructions are not clear, he must follow

national / local regulations.

1.2 Please check

You can register your re at: www.faber-res.eu

Check the re for transport damage and report any damage

immediately to your dealer.

1.3 CE-declaration

Glen Dimplex Benelux certies that this Faber re complies with the

essential requirements of the gas appliances directive.

Product: gas room heater

Model: Vejen

This appliance complies with the Gas Appliance Regulation (EU)

2016/426.

Harmonized standards applied: EN 613 2000/A1 2003.

This declaration is invalid, if without the written permission of Glen

Dimplex Benelux:

- Changes are made to the appliance.

- The re is connected to other exhaust materials than

specied.

2 Safety instructions

> Please note:

It is advisable to always install a screen for the replace if children,

elderly or disabled people are present in the same room as the

replace. If regularly vulnerable persons can be present in the

room without supervision, sufcient protection must always

be placed around the replace.

• The appliance is designed for atmospheric and heating

purposes. This means that all visible surfaces, including the

glass, can become hotter than 100 ° C. An exception to this

is the underside of the replace and the control buttons.

• Do not use the remote control and / or app outside the room

where the re is located. So that you are always aware of the

situation around the replace when it is being operated.

• The unit must be installed and subsequently serviced every

year and maintained in accordance with these instructions

and the applicable national and local regulations.

• Ensure that the data on the type label matches the local gas

type and pressure.

• The settings and the construction of the re must not be

changed!

• Do not place extra imitation wood or other smoldering

material on the burner or in the combustion chamber.

• Do not place any combustible materials within 1m of the

radiation area of the re.

• Through the natural air circulation of the re moisture and

uncured volatile components from paint, building materials

and carpeted oors, etc. are attracted. These parts can settle

as soot on cold surfaces. Therefore do not light the re

shortly after installation.

• Light the re for the rst time and run for several hours on the

highest setting, so that the paint can cure. Provide adequate

ventilation, so that any fumes can disperse; we recommend

vacating the room during this process.

> Please note:

1. All transport packaging is removed.

2. No children and pets in the room present.

3 Installation requirements

3.1 Minimum distance to combustible materials

around the re

• Keep a minimum distance of 9cm to the back wall and 50cm

at the sides.

3.2 Flue pipe and terminal requirements

• For the supply of the combustion air and the discharge of the

combustion gases you should always use the Flue materials

specied by Faber.

> Please note: Only when using these materials can Faber

guarantee the safe and proper operation of the appliance.

* This appliance must be installed in a chlorine-free

environment.

* The outside of the concentric ue material can heat up to

+/-150°C. Ensure, when penetrating a ammable wall or

ceiling, construction with proper insulation and protection.

Ensure sufcient clearance is maintained.

* Ensure that the concentric ue pipes are supported every

meter, so that the weight of the pipes is not supported by the

re.

* It is not permitted to start directly on the device with

concentric cut down pipe material.

The air supply could then possibly be closed.

3.3 Terminals

The combined supply and discharge can be done both via wall or

through the roof or through an existing chimney. Verify if the

position of the terminal meets the local regulations regarding

ventilation openings. The ue outlet can end on an external wall or

a roof.

Check whether the outlet desired by you complies with local

requirements concerning good function and ventilation systems.

> Please note:

For a proper functioning the terminal should be at least 0,5m. away

from:

• Corners of the building

• Roof overhangs and balconies

• Eaves (with the exception of the roof ridge, see Chapter 15).

Faber Vejen Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Faber Vejen

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info