Bedienungsanleitung Faber Vejen (Seite 9 von 20) (Englisch)

696805

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Installation manual

3.3.1 C11, wall terminal

For a facade or wall outlet use a wall terminal (see g. 1.0 C11).

Depending on the calculation this can be a diameter of 130/200mm

or 100/150mm.

3.3.2 C31, roof terminal

For a at or pits roof outlet use a long roof outlet with a diameter of

100/150mm (see g. 1.0 C31)

3.3.3 C91, existing chimney

You can also connect to an existing replace chimney. The existing

chimney functions then as air supply and a exible stainless steel

tube drawn through the chimney carries the ue gases. The exible

stainless steel tube of Ø100mm must have a CE mark have up to

600°C.

Use the short chimney outlet. (See g. 1.0 C91).

The chimney must have the following conditions:

• The channel of the chimney must be at least 150x150mm.

• There should be no more than one device on a chimney.

• The chimney must be in good condition:

o No leakage

o Well cleaned

For more information about connections to existing chimneys, ask

the installation manual “chimney connection set”.

4 Preparation and installation

instructions

4.1 Gas connection

The gas connection must comply with the applicable local

standards. We advise using a Ø15mm gas connection directly from

the gas meter to the appliance, with a shut-off valve in the proximity

of the appliance, which must always be freely accessible. Position

the gas connection so that it is easily accessible at all times for

service and that the burner unit can be disassembled. (See g.

8.0-C and dimensional drawing 16.2 for position of the gas

connection).

4.2 Electrical connection

The power supply must comply with the applicable local standards.

A wall socket 230VAC/50Hz must be installed near the re. For

power supply make use of the included plug adapter. See g 2.0 for

the wiring diagram of this connection and the LED Symbio module.

A = Plug adapter 6V

B = Micro switch

C = Spark transformer

D = LED Symbio module

E = Slider

4.3 Preparing the re

• Remove the re from its packaging. Open the operation door

(see g. 3.0), take the packaged parts from the re and

remove the bolts in the bottom plate.

• Prepare the gas connection on the regulator. See g. 8.0-C

and dimensional drawing 16.2.

4.4 Positioning the re

Take into account the installation requirements and the minimum

distances around the replace. (See Chapter 3).

4.5 Installing the ue materials

• When penetrating a non-combustible wall or ceiling the

opening must be at least 5mm larger than the diameter of the

discharge material. At a combustible wall or ceiling is this

100mm larger than the diameter of the drainage material.

• Horizontal sections should be installed with a slope towards

the re (3 degrees).

• Build the system from the re. If this is not possible you can

make use of an extendable adapter section.

• For truing up the exhaust system use the 0,5m. pipe, which

can be shortened and ensure that the inner pipe is always

2cm longer than the outer pipe.

• Parts, which are shortened, must be secured with a

self-tapping screw.

• Wall and roof terminals can also be cut.

• Do not insulate but ventilate built-in ue material (approx.

100cm²).

5 Removing the glass

5.1 Front glass

• Remove the front frame. See g. 4.0.

• Slightly loose the screws of the glass support under.

See g. 4.1.

• Slightly loose the nuts of the upper glass support and remove

it. See g. 4.2.

• Remove the front glass. See g. 4.3.

For replacing the front glass repeat the steps in reverse

order.

> Please note:

Clean all ngerprints on the glass; otherwise they will burn in once

the re is used.

5.2 Side glasses

For cleaning only it’s not necessary to remove the side glasses.

Only remove the front glass. See Chapter 5.1.

• Remove the side panel. See g. 5.0.

• Slightly loose the screws of the glass support under.

See g. 5.1.

• Slightly loose the nuts of the upper glass support and

remove it. See g. 5.2.

• Remove the side glass. See g. 5.3.

> Please note:

Clean all ngerprints on the glass; otherwise they will burn in once

the re is used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber Vejen Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Faber Vejen

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info