Bedienungsanleitung Faber Vejen (Seite 10 von 20) (Englisch)

696805

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Installation manual

6 Placing the decoration material

It is not permitted to use other or to add more material in the

combustion chamber.

Keep the pilot light always free of decoration material!

• Place the glass plate on the bottom in the recesses on the

left and right. See g. 6.0a and b.

• Spread the glass fragments over the glass panel (one layer)

and cover these with the supplied vermiculite grains.

(The amount of vermiculite affects the intensity of the glow

effect and can be done according to your own discretion).

• Place the imitation logs. Make sure that the logs are properly

connected to the tube burners and rest on the bottom of the

re.

If necessary remove glass fragments and/or vermiculite

underneath the burners. (See the supplied log set instruction

card).

• Spread the rest of the vermiculite and the chips over the

bottom of the burning chamber. Ensure that the air openings

are not covered.

Start the re as described in the user manual. Check the appearan-

ce of the ames and for burning against the vermiculite grains.

7 Checking the installation

7.1 Checking the ignition of pilot light and

main burner

Light the re as described in the user manual.

• Check that the pilot ame is not covered by chips and/or an

imitation log.

• Check the ignition of the main burner on full and low setting.

(ignition must be smooth and quiet).

7.2 Checking for gas leaks

Check with a gas leak nder or spray all connections and pipes for

gas leakage.

7.3 Checking the burner pressure and

primary pressure

Check that the burner pressure and primary pressure match with

the information listed in the manual. See Chapter 14.

Measuring the primary pressure:

• Close the shut-off valve.

• Turn measuring nipple A (see g. 8.0) some few turns open

and connect a measuring hose to the gas regulator.

• Take this measurement at highest setting of the re and when

the re is set to pilot light.

Do not connect the unit if the pressure is too high.

Measuring the burner pressure:

Check the burner pressure only with proper primary pressure!

• Turn measuring nipple B (see g. 8.0) some few turns open

and connect a measuring hose to the gas regulator.

• The pressure must correspond to the value indicated in the

technical specications of this manual. In case of deviation

contact the manufacturer.

> Please note:

Close all pressure measuring nipples and check for gas leakage.

7.4 Checking the ame image

Let the re burn for at least 20 minutes at highest setting and check

the ame for:

• Flame distribution

• Color of the ames

If one or both points are not acceptable then check:

• The log set layout and/or the amount of glass granulate/chips

on the bottom plate.

• The pipe connections for leaks (in case of blue ames).

• Whether the correct ue restrictor is tted. See g. 9.0.

• The outlet.

o Wall terminal right side up

o Roof terminal on the right position

o If the maximum horizontal ue lengths is not exceeded.

8 Instructions for the client

• Recommend that the unit should be checked annually by a

qualied specialist to ensure the safe use and to guarantee a

long service life.

• Give advice and instructions on care and cleaning of the

glass. Highlight the danger of burnt-in ngerprints.

• Instruct the customer on the operation of the appliance.

• Hand over to customer:

o Installation manual

o User manual

o Log set instruction card

9 Annual maintenance

9.1 Checking and cleaning

• Check and clean if necessary after verication:

o the pilot light

o the combustion chamber

o the glass

o the logs for breakage

o the outlet

o the wiring/contacts for corrosion

• Replace, if necessary:

o chips/vermiculite

o Glass granulate

9.2 Cleaning the glass

Most deposits can be removed with a dry cloth. Clean the glass

with Faber glass polish..

> Please note:

Avoid ngerprints on the glass. These are no longer removable

after they are burnt in!

Now carry out check-up as described in Chapter 7.

10 Conversion to other gas type

Conversion to another type of gas can only be carried out by a

qualied installer / dealer.

To do so, please contact your dealer.

Specify with your order always the type and serial number of the

device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Faber Vejen Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Faber Vejen

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info