Bedienungsanleitung Fagor CAT 44NG (Seite 26 von 104) (Englisch, Französisch, Portugiesisch, Spanisch)

485594

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

During the cleaning process the display

shows the following indications alter-

nately:

•«CLEANING 1 <1-6>»:

The program carries out 5 cleaning

cycles. The pauses enable the cleaning

solution to take effect. The cleaning

cycles are counted off in the display.

•«IN PROCESS»

The bar indication in the bottom line

increases with the advance of the

pause duration.

In the event of a power failure or

interruption, the program must be

restarted!

The cleaning process takes ca.

8 minutes. Then the following is shown

in the display:

•«

•

EMPTY WASTE CONTAINER -

PRESS OK»

«WAIT»

Empty and replace the container. Then

press the „OK“ key (Fig. 3, g).

•«REFILL WATER – PRESS OK»

Remove the water tank, refill water

and replace. Then press the „OK“ key

(Fig. 3, g).

•«CLEANING COMPLETED»

When this message appears, the clean-

ing program is ended.

Turn the bean container to the desired

position. The machine is now ready for

use and in the status of the last

selected coffee mode.

After running the cleaning program,

you are advised to throw away the first

cup of coffee from the machine.

13.7 Running the descaling programme

The descaling programme allows a

simple and effective descaling of the

appliance. You should descale the

appliance at regular intervals, latest,

however when you are informed by the

display indication “CARRY OUT DESCA-

LING“. The descaling process is carried

out in 2 phases, takes several minutes and

should not be interrupted.

The frequency of descaling depends on

how hard the water is in your region.

Please do not forget to find out the water

hardness and adjust the corresponding

hardness degree on the appliance. Please

read chapter “Determining and adjusting

the water hardness”.

Use only limescale removal products

recommendes by FAGOR. You may obtain

them from our authorised distributor

network or through our customer care

helpline.

Method phase 1: descaling

1. Press button f “Menu “. Subsequently

press button c “Scroll “ or button d “Scroll

“ until the menu point “DESCALE“ ppears.

2. Confirm the menu point with button g

“OK “. If you press button g “OK “ once

more you will receive instructions via the

display how you have to prepare the

descaling. Follow the instructions on

the display:

• REFILL <250ml> WATER changes with 125ml

DESCALER IN WATERTANK – PRESS OK.

3. Pull out the water tank. Put 125ml

descaler agent into the water tank. Then

add 250ml water into the water tank by

filling the empty descaler bottle twice

with fresh water (see Illustration ). Replace

the water reservoir – press button g "ok “,

the descaling program starts. Fig. 34

«PUSH IN WASTE CONTAINER»

Replace the container.

«WAIT»

The brewing unit is positioned.

«WASTE CONTAINER UNDER OUTLET»

Place the waste container under the

outlet again.

«PRESS OK. CLEANING 6 <1-6>»

Rinsing phase.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fagor CAT 44NG Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info